Bench Power Supply Variable 30V/10A High Precision Adjustable CC/CV Regulated Power Supply with Alligator Clipqs for Lab Equipment, DIY Tool, Repair, Electronic Testing,Tinkering

Purchased this to anodize aluminum in the .58 square foot size using the low current density method. Also successfully used it for etching aluminum. Works well for constant current. Numbers were easy to read, and no overheating problems with 2 hour runs. I didn’t test it for accuracy against a multi-meter. It has no hum. Nice small profile.

Both voltage and amperage are easily adjusted with both coarse and fine adjustments. The posts are set up to take a variety of leads and has side holes to accommodate a simple wire without end plugs. For the money, it's solid. I use it to inject voltage into various areas of motherboards for troubleshooting and it is helpful to have a power supply that can lock the voltage and draw current as needed or lock the current and draw voltage as needed. The display is quite clear and large enough to see at a distance well beyond arms length. Hope this helps.

This is a review of the NaviTech NP3010H power supply received on 9/23/2019.Low voltage and low current setting control is good. Turn coarse voltage or current all the way to zero when needing low values.Voltage adjustment: With coarse voltage = 0V, fine adjusts from 0.00V to 3.55V, with 0.01V precisionCurrent adjustment: With coarse current = 0A, fine adjusts from 0.000A to 0.958A, with 0.001A precisionMeter accuracy (Agilent 34411A 6-1/2 digit multimeter used for these measurements) VoltageSet VoltageMeasured 0.80V 0.799V 1.20V 1.194V 3.30V 3.291V 5.00V 4.991V 10.00V 9.983V 20.00V 19.994V 30.00V 29.901V 32.00V 31.906V CurrentSet CurrentMeasured 0.100A 0.0896A (25ohm load) 0.500A 0.4885A (25ohm load) 1.000A 0.9715A (0ohm load) 2.000A 1.9505A (0ohm load) 3.000A 2.9307A (0ohm load) 5.000A 4.8940A (0ohm load) 10.00A 9.82222A (0ohm load) 10.18A 10.0002A (0ohm load)Power supply noise (Tektronix MDO4104B digital oscilloscope with 20MHz bandwidth limit enabled for these measurements)50.2mV peak-peak, 2.45mVrms (25ohm load at 12V, DC-20MHz, 100Meg samples/sec)26.3kHz time domain switching peaks6.02MHz and 14.1MHz frequency domain peaksStartup Transient Response9.3ms 10-90% rise time from cold turn on 0 - 12V into 25 ohm load21.5ms settling time to within 50mV of 12V (25ohm load)19.8ms settling time to within 50mV of 12V (no load)No overshoot in either case.Note: Current limit must be set high enough to remain in voltage mode. If not, I did see 0.58V overshoot on the 12V startup transient.Shutdown Transient Response89ms 12V to 0.5V into 25 ohm load6.00s 12V to 0.5V into no loadShutdown transient response depends upon the load, and if there's no load, can take 6 seconds from only 12V.Front panel binding posts lack a center hole to thread heavy gauge wire through. Wire tends to slide off the binding posts even when tight. If you bend the wire in a half circle the diameter of the binding post, it holds better. This is the weakest feature of this power supply.Current metering accuracy is pretty bad at low currents, 10% error at 0.100A current set.Besides the two above negative points, the rest of the power supply performs very well for a switcher. I really like how small and lightweight it is.I'm using it for power input to a 3-phase stepper controller to drive a brushless DC motor, power for a 12V air mattress blower, power for a 12V compressor to pump air for car tires, and power for charging sealed lead-acid batteries on replacement UPS (uninterruptible power supply) batteries.When charging the valve regulated sealed lead-acid batteries, I use 14.2V with a current limit of 1A. The changeover from 1A current limit to 14.2V voltage limit is smooth as the current drops to less than 50mA @ 14.2V when fully charged.

Arrived fast, it's a good power supply, instruction are easy to understand

Easy to use with adjustable Voltage and Current limits.

Severe quality control issues. These are photos of the unit 30 seconds after opening the box. Apparently the manufacturer doesn't care what condition the units ship in.

After trying out a few other budget options, this on is a definite keeper. Let's start with the CONS....- The potentiometers are touchy. Even the the "fine" know feels way too touchy when you get the 4 digit unit. I would have liked muti-turn knobs a lot better, but to be honest, the knobs are OK, just not perfect.- The fan speed is proportional to the current drawn, not how hot the power supply is. This is weird, but hey, it's a pretty small con.- Depending on how clean of a power supply you need and how quick of a reaction you need, this PS may not be ideal for you. I haven't tried it on radio equipment yet, but there are a few tens of millivolts of noise and the output capacitors are fairly large so the transition from CV to CC is relatively small and may burn current-sensitive components like LEDs if you set your voltage too high and count on the CC to save you.And now for the PROS...- This power supply does pretty much what it needs to do and at $120 for the 300W 4 digit version, it is definitely worth it. I have charged lead acid batteries, excited alternators, and run digital electronics at all sorts of voltages and current levels for long hours and the power supply keeps going and doesn't get hot. The current and voltage displays are very close to my Fluke 87 and someday I will calibrate both to get even more confidence out of the reading. You don't really need the 4-th digit as the accuracy is not that great, but I find it convenient to have for not that much extra $The form-factor of this PS is amazing. It is tiny, light and convenient. I don't know how to praise it more.... All I can say is: If you're in the market for a mid-range bench power supply and if you can afford this, definitely get this on. I needed the 60V option where the offerings are more limited and this product fit my bill and needs perfectly. I would have payed a little more for a 10A version if one was available and as nice as this one.

This power supply unit works great. But after almost one year of daily use, it broke. I got a very strong burning smell one day and the power supply soon stopped working. After contacting the seller, I got a response within hours. Sent in some pics of the internals for them to confirm the issue. Eventually a replacement unit was sent out under warranty. I am very happy that my set up is working again!

電圧及び電流か可変でき重宝してます、使用上の注意はバッテリーに繋ぐ前に供給電圧測定、電流にしてから繋いて下さい逆流防止の為。

構成された測定器で、出力を測ってみたらほとんど誤差はなく信頼できる製品でした。微調整ボリュームが主ボリュームと別に付いていますが、過去の使用機器は殆どが二重ダイアルになって、分かり易く出来ていたので使用時に違和感を感じましたが、これは慣れでいけると思います。小型での扱いも場所を取らないので尚結構でした。

60V電源が欲しくって購入した。買って分かったことであるが、機能的に現在持っている同価格帯の30V電源より劣るようだ。また、ファンの音がうるさい。静穏タイプのファンに交換をしたが、結局のところ、再度「 ”他社製品”」 を買い直し購入した。（お蔵入り）いい勉強になった。よって、現状の当該製品は他者にはお勧めしない。メーカには改善を期待します。

必要は電圧を供給できるので、便利に使えます。

何10年も前に作った自作の安定化電源を持っているが、最近買った電圧制御回路の電圧を調整をしたかったので、購入した。廉価だったが、微調整が出来て、回路のシャットオフ電圧などの設定が容易だった。