Full Motion Monitor Wall Mount

I am using this wall mount to hold a 23" Asus computer monitor. Right out of the box I was very impressed by the quality of the mount. The articulating arms are thick aluminum castings and the pivot points are cone shaped which is a great design for a hinge that needs to be locked in place or move with some resistance. The monitor mount fit the threaded holes in the Asus monitor holes perfectly as per the standard, The screws that hold the X brace to the arm were a tad loose and needed to be tightened. The wall mount was attached to a 1/2" sheet rock wall using 9/16" toggle bolts (I didn't use the plastic anchors that come with it, as I was afraid they would pull loose from the sheet rock.) The toggle bolts are just a dollar or two at Depot/Lowes and give the piece of mind that the whole unit won't come crashing down if the kids pull on it. The mount also came with a small bubble level which came in handy when marking the holes on the wall. I extended the arm out to the side flush to the wall and set the bubble level on it to ensure the arm was horizontal and the screen would sit level. Worked great! After attaching the monitor I noticed that the arm was binding when the knobs were tightened to be snug but not lock the pivot points. So I took it apart and put a dab of grease on each cone hinge and reassembled. Now when the knobs are just snug, the arm moves smoothly with a nice amount of resistance. When the knobs are tightened more, the hinges will lock in place. I even put some grease on the tilt hinge to make it move smooth. I was hesitant because I was afraid the screen would tend to fall forward and not lock in place, but that did not happen. The tilt knob is tight, and the screen can be tilted forward and back and it holds it position. The power cord and video cable were attached to the arm with tie wraps for a nice neat look. Even though I give it 5 stars, I have these criticisms: - It came with anchors, but toggle bolts would have been better. - The 4 screws you can see in the picture of the X bracket were not fully tight. I had to disassemble it all after installing to tighten them because the screen rocked side to side a bit. - Had to disassemble it all again to add grease so it would move smoothly and not bind. Other than that, it works as it should. It is solid and does not wobble or sag. It is made heavy duty enough to handle home use. The toggle bolts hold it solid to the sheetrock. Would have preferred to screw it into a stud, but I had no choice as there was no stud within a few inches of where I wanted to mount this. All in all, it gets a thumbs up. And for the price, you can't really go wrong.

It's a Wall MOUNT... which Works for 24", but here are some IMPROVEMENT Suggestions, especially when hanging larger Monitors > 1. SHOULD Have a WIDER Mounting BASE accommodating ( 4 ) SCREWs for added Strength & Stability (Esp. for larger Monitors). If you Live in CALIFORNIA where EARTHQUAKES Occur often enough, IT would only take ONE Screw to Pull Loose causing your Monitor crashing down.. either Breaking into pieces, OR worse... Falling on your Baby's Head crawling along the Floor on her blanket..... 2. SCREW Holes should be Larger Diameter .. accommodating larger 1 / 4 " - 5 / 16 " Screws or Lag Bolts... (4 Holes and 4 Screws ) ! 2. The Tightening Knobs tend to Loosen after Swinging Monitor dozens of times, No Problem IF you just keep Monitor in One Position. But a Fibre-Lock-Washer + Flat Washers could help ..... Preventing the Knobs from Loosening over Time, of course requiring next size larger Screw threads beyond both Knobs. Otherwise.. this Mount suit's most functions , and is of Good High-Quality..

Used it to mount a 28" flat screen into a recessed cutout. This mount allowed the TV to be hung on the installed and extended arm, then pushed straight back into cutout. Easy to mount; sturdy; all swivel joints can be tightened to be as stiff or easy to move as you need; Very wide range of motion. Had to cut down screw length to fit my particular TV, but that is understandable. Incredible price for what seems very good quality.

I got this mount to originally put a 32" tv on. I figured since the tv only weighed 17 lbs, the mount would be fine since it's rated capacity was 33 lbs. After getting the tv home and realizing it was a little to small for our game room, I took it back and exchanged it for a 40'". The mount was already on it's way so I figured I'd give it a try. I fabricated a bracket that mounted to the tv, drilled that out and attached it to the wall mount. It worked but the tilt mechanism of the wall mount didn't seem quite strong enough to keep the 40" tv from slipping down. As I tightened the knob with a pair of pliers I felt that familiar feeling of it stripping out. As it turned out, the metal screw mating surfaces didn't strip out, it was just the plastic knob that was slipping on the bolt. I removed the plastic piece and sacrificed a pair of vice grips to replace the plastic piece. It worked great. Only reason I give it 4 stars instead of 5 is the plastic piece failing. After tightening with the vice grips this little mount is working great on a tv much larger than it's rated for. If you're going to get this mount for a bigger tv than it's designed for, you should be good at fabricating and improvising. The mounting bracket with this wall mount kit is pretty narrow at only 200 mm from bolt to bolt. I've got to give to this little beast. Aside from the plastic covers on the bolts being poorly attached, it's pretty rugged. It's holding a 40" for us and it's not going to let go of the tv.

This is absolutely brilliant. The price is realistic - about a tenth of the 'branded' ones. It is extremely well built. The range of movement is unsurpassed. Comes complete with screws of different depths and spaces. No brainer.

When ups delivered a box to me I was wondering where the lcd mount was. When the parcel was opened I found a box 7inx8in. The lcd wall mound was in there and was very impressed by the quality of this unit. It came folded up in box and came with all the machine screws for panel and wood screws for mounting it to wall. They really shouldnt include plastic wall anchors, which could be used if installing into concrete but NOT drywall. I screwed directly into a wall stud. The unit extends out aprox. 16inches and panel can be tilted down, I have a 22in monitor mounted over a 24in. Works great and very impressed with a wall mount for $22

Compact, yet sturdy, this articulated arm fits our project perfectly. I purchased 12 arms so that our organization could hang paintings to hide oxygen outlets in patient rooms at our hospice. A medical necessity, these outlets took away from the home-like environment we create for patients. Now nurses can simply swivel a painting away, connect the oxygen lines and swivel the painting back in place for a beautiful room. It's a smooth one-finger operation that's easy for staff and keeps the rooms looking beautiful.

allot cheaper then the hi street an very easy to put up and take down. holds the TV's well on the walls

Very happy with these mounts. Bought 2 to hang my 27" Thunderbolt Displays on and they work perfectly. The hold the heavy displays without a problem and the articulating arms make it easy to adjust the displays right where I want them. I am very happy with the quality of Mount-It! products, don't let the low price fool you!