Sound Storm Laboratories EVO3000.1 Class D Monoblock Car Audio Amplifier - 3000 High Output, Low Level Inputs, Hook Up to Subwoofer for Bass

Love it! Upgraded from one of their smaller, older amps to this one and its performing great.

This is one of a few SSL amps I got and I've been satisfied everytime ! I use them myself and also for friends. I have one of hese installed under the front left seat of a Nissan Navara and the fit is great. Love the simple crossover and the sound is enough for a single 12" shallow sub at 400W rms. The Pioneer TS-SW3001S2 can handle 400W rms with it's single 2ohm voice coil and this amp slams it good !! Could not be happier.

I'm giving it a 3 star , didn't come with everything I was missing the manual and the bass knob along with the cord then it took me forever to get some sticky stuff off of it other than that it works well just gets hot qick but it works

Having purchased many less than top of the line amplifiers, I was not expecting this one to exactly go above and beyond the call of duty. And to be honest, it hasn't. It has however met my expectations in most areas in disappointed me in at least one. To begin, I have this amplifier pushing one 10" Pioneer Champion Series Pro (800RMS@2OHMS)(3,000MAX@2OHMS).This amplifier advertises a 1000 RMS rating @ 4 Ohms, so you must think i'm crazy, but anyone with experience in budget amplifiers can tell you that the advertised ratings often don't relate to reality. I haven't measured it, but know that at most this amp could power 2-mid level 10's or 1 high-level 12 at most. 2 12's would definitely be pushing it. Now let me break things down a little bit. Appearance, definitely 5 stars here, the brushed metal finish is very nice, I did notice however that it is relatively easy to scratch. Sound Quality, 4 Stars, not blow you away kinda jams but if you tune it properly you can make it sound top notch. Heat Displacement, 3 Stars, the heatsinks on this thing look nice and are pretty large, but many does this thing get warm to the touch. After playing music at around 85% volume for an hour this thing is almost hot to the touch. I'm using it at 2 ohms which it's rated for, but it still worries me a little bit as I know some amps will fail if the heat becomes to great. (You should also know this is a class A/B amplifier, which means it is not as efficient with the power it consumes(as opposed to a D Class amp), which means it produces more heat.) Overall, 4 Stars, I know the people who are looking at amplifiers at this price level are budget-conscious of their purchases like I am (18, college student), but amplifiers are the kinda thing where it's YOU GET WHAT YOU PAY FOR. Simple as that to be honest, don't expect the world for >$100. Happy Bumping! Brian.

I had it for 7yrs now and still working strong pussing 2 12" ls7 no I have 2 15" 1k rms each and push them strong,now is time to get the 5k watts amp.

The amp came on time and packaged well. Installation was easy in spite of the limited documentation. Should be expected from a "budget brand". My only complaint is when I got it all hooked up and I fired it up I noticed a faint thumping noise in my subs. They would thump about once a second. I got a bad unit. It happens. Amazon is sending a replacement even as I write this review. I will update when I get the replacement installed. However, I did put the amp through its paces just the same. I was pleased that the 1 ohm rating was not inflated like a lot of budget brand items found on amazon, but I'm fairly certain the power rating is. The amp is fused at 105Amps. Simple math ( 105 Amps x 13.6 Volts = 1428 Watts Max ) shows that the max power is substantially lower than the claimed 4k. The RMS rating for 4 ohms is more likely the correct Max rating for 1 ohm. The only good news though. This thing drives like a 1500 Watt amp should at 1 ohm. UPDATE: So I got the replacement pretty fast. I finally installed the replacement and it has the same exact problem as the first one with an added flaw. I now hear radio interference in my subs as well. The popping in the new one isn't as bad but still makes the same noise with the same problem. Now, I know some people will criticize my setup claiming my installation is the cause of the problem. I'm not new to car audio, so I know how to eliminate other items as the cause. After disconnecting everything but 1 sub wired at 2 ohms and powered and turned on directly by a battery (no chance of outside equipment affecting the amp), the problem still persists. Good ground connection to bare metal with 1/4-20 bolt and nut and soldered lugs(I don't trust just crimping in high power DC circuits). No RCAs connected. Head unit taken out of the line. Subs rewired to 2 ohms even though the amp is 1 ohm stable. I even swapped in my trusty 7 year old Panasonic head unit. Same problem. I was going to at least give 2 stars because it's powerful and is 1 ohm stable, but the lack of consistent quality doesn't permit me that freedom. I seriously considered keeping it since I probably could live with the noise now since it's much quieter than the first unit, but I can't bring myself to justify the poor sound quality in my setup. That and I worry about the amp having a catastrophic failure at the expense of my brand new Polk subs. I'm also returning the SSL EVO1600.4 4 channel amp I purchased for my 4 corners. The only reason I bought that one is because it matched this one. Instead, I will be spending $100 more than these two amps cost to get a Polk D5000.5 5 channel amp that is a near perfect match for my speakers, which are conveniently all Polk also. Though I will have to tear down my trunk again for the 3rd time since I started this build, it will be worth the peace of mind. Pros: true 1 ohm stable though the rating is seriously inflated, this still works out to be a pretty serious 1500W @ 1 ohm amp Cons: first unit was defective. Had a steady "switching" noise coming through the subs about every second. replacement unit was also defective. Same "switching" noise with the added benefit of hearing radio interference as well Summary: My first impression was that this is a good amp and I just got a bad one the first time. It happened twice. 2 out of 2 amps were bad. That doesn't sit well with me. My advice: Scrape together a few more pennies and get something from a trusted quality brand like Polk, Alpine, Kicker, Pioneer, JL Audio, Sony, MB Quart, Hifonics, and the list goes on. If Amazon wants to make this right somehow they can credit my account to help compensate for the second bad item in a row

Happy with the build quality of this amp very nice metal finish have yet too hook it up I am waiting on power wire so will make another review when I get it pumping. Only down side is the terminals there slanted downwards instead of straight so kinda hard to find 0 to 4 gauge reducers so I just went with a distribution block with only 5 inches of 4 gauge. Update. Amp is beast have it on 2k Rms and not even turned all the way up have it hooked up to a sundown x12 d4 with upgraded voice coil and surround. Amp doesn't get hot or even warm running at 2 ohms. Filters work good and so does the 180 degree switch. Highly recommended amp all my friends want one now. Have 0 gauge from battery to distribution block then down to 4 gauge try to keep the 4 gauge as short as possible so can get more power. If someone can find a set of reducers to go in there I'd love to see them. Also have 8 gauge speaker wire good tight fit. Will post pictures once I get everything cleaned up.

It's enormous.

I recommend this

It pushes very very loud nice crisp bass without any issues for more than a year..still works flawlessly. If you know how to handle the gain and the crossovers of course

Pushes my Sony xplod very well, impressed so far.

très bonne ampli pour le prix ... très satisfait