Farmertec 92cc Holzfforma Blue Thunder G660 Gasoline Chain Saw Power Head Without Guide Bar and Chain All Parts are Compatible WT MS660 066 Chainsaw with Normal Handle Bar

Excellent saw! I have a Stihl MS 150 and a Stihl MS 261. I needed a large saw that would handle a 36" bar for a large maple tree that fell. The Stihl MS661 at $1,400 was just more than I could afford, so I bought this G660. I paired it with an Oregon 36" bar and chain. The pictures are from the first use. I figured it would take forever to make the cuts because I was running it slow for break-in. It didn't. It ate that maple tree for breakfast. Wow. Easy to start (2nd pull from cold, 1st pull from warm), runs smooth, and it just rolls the power on. I'm very pleased. One note: The factory does not set up the carburetor needle valves. You have to set them or the saw won't start, it will flood. YouTube Steve's Small Engine Saloon has a good video about how to adjust chainsaw carbs. Build quality looks very good. Hopefully it will last a long time.

Seem to be built very good. i put it together and put a bar on it, within 4 pulls it started right up and idled great as it should. I cut a tanks worth of wood with it the 1st day and it pulled a 24 inch bar easy without getting bogged down. Can't wait for it to get broken in and put a 36 inch bar on it.

Powerful. If you do not follow stsrting directions to the tee, it will not start.

I have a 36 in bar on this 660 saw and it cuts the hard Juniper like butter I was hesitant but the only issues I've had so far was the chain adjuster which I would 100% recommend getting a stihl chain adjuster and to be very careful with the pull start must use the decompress valve or you'll end up breaking the string

I was scared that this Chinese saw would be a piece of crap. I put a 36” bar on it and milled a 10’ long 30” diameter oak log into 8/4 inch slabs. It works great. The manual contradicts itself regarding the oil/gas mix. I bought alcohol free gas and mixed it 50:1 with Red Armor. It starts the same and runs great every time.

I was reluctant to buy the knock off of the 660, but the price was just to good to pass up. I needed a more powerful saw for milling. I've been running this with a 42" bar. It's broken in now and running very well. Haven't had any issues with it, although I've only run about 6-7 tanks of fuel through it thus far.

Nice saw - solidly built. Started in 3 pulls! Seems like it was missing a screw - only three screws provided for mounting the handle. Handle was different than the one pictured but that's ok. The inner log dog will not fit without modification but I don't need them anyway since this will mainly be used for chainsaw milling.

This Saw is not what they say it is. After break-in procedures the saw ran for about 10 minutes and the crank bearings came apart and the piston stuck in the cylinder. after a month of Emails and getting nowhere to get the saw replaced, ( they wanted to send parts out for me to fix the saw which you have to have specialized tools to do so) they finally offered to have it ship to somewhere in the USA to have it fixed and sent back, with no time frame. so if you want to be treated like crap and told if you don't do what they want your out of luck on the saw go with farmertec. Ojenas saws are much better quality did not have a problem with them so don't waste you money on farmertec , read all the reviews before making a choice

Update May 17 2021, saw worked great milling softwoods with a 25'' bar, ran great, started great and lots of power. It has burnt about 20 liters of gas. Crankshaft just snapped right behind the clutch in the middle of a cut, motor still runs fine. Parts are ordered, will fix and see if it was just a bad luck or more issues coming. I am rating this as a Holzfforma and not as a Stihl even those it's almost the same thing in looks. I received it within 10 days everything was in good condition. I am aware some things are recommended to look at, i did check head bolts which were fine. Muffler bolts some were loose and i did add loctite, i check carb nuts and decomp which were fine, also grease the needle bearing in the cluth. The chain tensionner is not very smooth, i will do the shim to it shortly. Plenty of videos out there with things to check over, i have not replaced any parts as some suggest. I did a break in and I am down about 10 tanks of gas so far doing some milling. It started great the first day and still starts perfectly every time. I needed more power than my other saw for milling, this one is perfect for me, i have the power i needed at a great price, i could not justify spending 1500$ for a Stihl of the same size.

Good for at home use.it was delivered with a clogged carburator but after cleaning it runs great. Ran it with a mill without issues. Plenty of power for occasional use for the price.

Well this saw has had over 30L of fuel burnt at 40-1 and hasn't missed or popped once. One pull starts. The seller had it tuned and a good spark plug installed. It runes so good that I'm buying another one. love it. My MS 661 and 660 haven't left the shelf since I started this saw.

Missing parts (no handle screws, no spiked bumper), cover cracked, and WOULD NOT START. Tried many times (with new gas). Vendor mentioned 25:1 for first 10 hrs. Tried it, no difference. Don't need this hassle with a new product. Was told have to ship 3700km at my expense to get refund! Thankfully Amazon intervened.

Great product. Works great.