CALPALMY 10-Pack 11x14 Clear PET Plastic Sheets, 0.04" Thick Flexible Transparent Panels, Shatter-Resistant Plexiglass Alternative for Picture Frames, Signs, Displays, Crafts & DIY Projects

All sheets arrived flat and in perfect condition. These worked very well for lining two 10"D x 16"W wire shelves, twelve shelves total, with four whole extra sheets to spare. Of course, the shelves ended up being slightly smaller, but it was easy enough to cut with a good pair of sharp scissors. It isn't at all brittle. I could cut a tight semicircle in every corner so the lining was snug around the shelves' round legs with zero cracking.They're rigid and don't bow at all in my application but you may need 2mm or more for larger shelves with wires spaced further apart. As you can see, this product is 0.04" (1mm) thick.I used the end scraps from that project to make AM/PM dividers for every compartment (28 total) of my pill box, making it a daily organizer. Very versatile, very pleased with this product.ATTN people complaining of haziness and scratches: PLEASE remove the protective film! It's thin, can be hard to detect (and peel), and ON BOTH SIDES OF EVERY SHEET!! 🤦‍♀️

I don’t think I’ve ever written a product review, but considering this item has ‘frequently returned label,’ I decided to go ahead and write one! This is a good quality ‘ thickish’ PET plastic that is perfect to just help protect something- it is NOT fiberglass - so if that’s your need look somewhere else…it was delivered promptly, packaged well, and worked perfectly for my needs… the material is just as described and I think I’m going to find a LOT of uses for it! As you can see in the picture, I used it to cover a shadow box, edge to edge…

These PET panels are great quality, nice clarity, no warping, and they cut cleanly without cracking. Perfect for crafts, signage, protective covers, or any DIY project where you need something lightweight but durable. The 10‑pack is a great value.

Good quality and large sheet

Bought these for a signage project, and they worked well for what I needed. The sheets were easy to work with, clear, and provided a nice finished look. Having five in the pack was convenient and gave me extras for future projects. Good value and I’d buy them again.

Fast delivery, good product

I purchased these PET sheets intending to laser cut small paint stencils on a 50 W CO₂ laser. The listing suggests PET plastic sheets, which led me to believe they would behave similarly to polyester/Mylar stencil film.These sheets are approximately 0.04" thick rigid PET panels. Under a CO₂ laser they do not cut cleanly. Instead they soften and melt, producing rough edges and re-solidified plastic. This makes them unsuitable for precision stencil work.For anyone purchasing this for laser cutting: this is not the thin polyester stencil film typically used for laser-cut stencils (usually 4–7 mil). It behaves more like rigid craft plastic than stencil material.The sheets themselves may be fine for crafts, protective panels, or Cricut cutting, but they are not appropriate for laser stencil applications.

Nice thin plastic. Used and had to cut with razor knife. Worked well for small candy dispenser.

This is not the type of plastic that will snap with snap when bent, in fact you can bend edges into it if needed. The plastic itself can curve and roll - and will curve/not hold its weight if propped on an angle (at least by the whole sheet).The plastic itself is solid and clear and cuts pretty easily with either a heavy duty box cutter or sharp scissors for crafts.I used it to create side barrier (cut into 12"x36") for my work table and applied UV film to block out any sunlight coming from the gap between my monitors and table. At 12"x36" (half the width) it is sturdy enough to sit upright without curving as long as it's mounted properly along the length.Overall it is as advertised.

I used this to protect my outdoor tv, and the thickness is perfect for what I needed it for. Great buy for good quality

I used them to build an enclosure for 3D printer. Frame from wood strips, used table saw to make slits then slid these sheets in. Yes they are 1mm thin, but that's not an issue, there is no reason to spend money on thicker sheets. They do the job. Added fans and vent and the enclosure is perfect.These sheets are not brittle, don't break or chip. This is a second enclosure I built this way and would recommend these sheets. When you are making enclosure, work from the sheets, try to fit the enclosure frame to the sheets so you don't need to cut them.

GénialMis dans la porte moustiquaire pour éviter les bris de chatsSe coupe super bien et fait le tire de la hauteur de la porte donc parfaitBon prix et bonne qualité

Perfect. Exactly what I needed.