VARSK Grease Gun Coupler, 15,000 PSI Burst Pressure, Heavy Duty Quick Release Grease Coupler Fits All SAE and Metric Zerk Fittings and All Grease Guns - 1/8” NPT Fitting - VA409

I think Im in love.I had purchased a brand new grease gun from a local big orange store and the zerk nipple would get stuck to the zerk fitting. I had to gyrate and twist it around and lever till it came off. Awful.I put this new grease coupler on and my goodness it is nice. I know some reviews might be B.S. but listen to me now, this thing is saving my time and sanity.It will be used to regrease my tractor front loader. There are 8 zerks per side and they need a little extra every every so often.I've had probably 8 different grease guns in my life and while not all of them caused my as much hassle as the one I mentioned above, they will always leave some grease on your fingers. This new one seems to keep my hands clean. And it isnt spitting grease backwards as the latch makes a super strong engagement.The one downside I could see it that it is bulker so it might not fit in very tight areas like a u joint in a driveline. But then again it wont fall off as your pumping so it might work better.I turned my crappy gun into one I dont mind using. Just get this.1

I needed a grease gun. I was reluctant to buy one online w/o a chance to inspect it and heft it, so I bought one at a local brick-and-mortar. The gun was fine, but when my neighbor and I tried to use it while rebuilding my mower deck, the supplied coupler would go on to a zerk fitting but would not come off. We ended up having to use a pry bar to remove it. We didn't try again. (When I found the gun I had bought on Amazon, I saw that others had reported the same thing.) I went in search of a replacement zerk coupler and found this one. Chose it on description, ratings, and price. When it arrived I was impressed not only with its construction and operation, but even with its packaging. All were first-class! Tried it out that afternoon and it worked like a champ. Exactly as represented and as it should. Bought one for my neighbor, whose own zerk coupler had gotten "tired" and would no longer stay connected. Solved his problem as well. Highly recommended!

This coupler cost more than the cheap grease gun I put it on and I don't even care. This is THE part of the grease gun that matters, so you need the best product....this is it. If you asked me if I'd ever be writing a review for a grease gun coupler, I'd have laughed and said no, but here I am.The junk coupler that comes on most grease guns sucks because you have to snap it on. Unless you have plenty of elbow room and gorilla strength grip, it's really hard to snap them in place. This one is so easy to get it latched onto a zerk and so easy to get it off because you just squeeze a lever to open/close the jaws. They really do lock on tight too. I bet you'll break/bend the handle on your grease gun before this coupler lets go.Hard to believe it's worth the price, but I'm a believer now. I use my grease gun as often as I should now that it's this easy.

Worked as it should, ended up removing after I purchased because I could only get it to work on about 1/2 of the grease fittings on various pieces of farm equipment. Ended up back with my loc-n-lube. I bought this because my loc-n-lube was leaking only after about 5 tubes of grease. I contacted the company and then sent me a replacement seal that fixed the problem and no cost to me. On this one....I really did not like the lock lever, it was hard to use (when I cold actually get it on a fitting).

You will definitely get a high grip/seal on Cordyceps. In this process, you will not be able to completely eliminate all excess grease from the grease, because when you disconnect, the pressure will spit out some grease. However, due to leakage around the coupler/tank interface, there will not be a lot of grease around the tank. After decoupling, dry quickly with a rag/tissue and move to the next position. If a manual pump oil injector is used, the grip of the connector is strong enough to allow manual oil injection twice. It’s really good. The parts they provide can be used to update the connector on the first purchase. Great product.

We must build a solid extension shelf 14 inches long. When the standard coupler is not released, the extension will be interrupted at the thread. Flexible hoses simply won't work.Bought this, Hallelujah! The angel is singing, and I am now lubricating! This thing will almost never disappear! Straightforwardly love a good tool, this is the one.The VARSK at the end of the 14-inch solid extension rod has been successful. The price of other brands of quick connectors is almost twice that. VARSK solved a unique problem! There are 6 "problem locations" on the machine-weekly attention is required. Thanks VARSK!!!

The construction and operational characteristics of this device is excellent, but too bad that the tip is so large that it won't fit into many of the fitting locations on my tractor. The tractor requires greasing every 10 hours of operation, so I was very selective in my choice of a new grease gun and coupler fitting. Good thing I still kept my cheapo grease gun that has the standard push on tip that has a diameter that fits in the location of all of the other fittings. They are not as easy to grease as this one, but at least the old style coupler fits. But what's really disappointing is that I now have to use 2 grease guns to get all of the fittings done on the tractor.

The item arrived in quality packaging with extra parts and accessories.The Grease Gun coupler fitting is very solid and uses a mechanical lever to clamp on to Zerk Fittings.While the item is a little larger than a normal coupler and it may take correct positioning if you are in a confined space, I feel this is an adequate trade off to ensure grease is not going to waste.The quality of the item makes me feel like it will last me lifetime of use.