TORACK Bike Storage Rack, 6 Bike Rack Wall Mount Home and Garage Organizer, Vertical Bicycles Hanger Hooks for Indoor Space Saving

This bike storage rack has been a lifesaver for our family! It’s sturdy and holds all our bikes safely, which means no more tripping over bikes in the garage. Easy to assemble and makes getting the kids’ bikes in and out a breeze. Totally worth it for keeping our space tidy and stress-free!

Super functional. Because of the design hanging on the wall it frees up a lot of space in your garage. Great for smaller spaces. They’re very stable and hold extra large bike frames with ease. They’re easy to install and took my husband under an hour. The bikes are stable while one the rack and very safe while hanging. I don’t worry about my toddler walking by them. Great value!

Can you hang 6 bikes with this rack? Yes, but not as pictured on the product page with all three sections of rack being mounted side-by-side and flush together. It's important to center each rack across wall studs, or mount on wood paneling that is anchored into wall studs. Two bikes can fit on each section, but there must be spacing between the racks. This rack system is not made specifically for bicycles. In fact, the literature that comes with the rack doesn't even mention bicycles - it shows an assortment of attachments and tooling. It's safe to say that bikes would be the heaviest thing this rack system can handle, and proper mounting is key for stability and safety. Hanging & removing bikes from the rack takes care; pulling down on the bike could bend the hook, break the mount, damage the bike, or even cause injury. It's not something I want my younger kids doing, so only larger bikes for older children will be mounted at our house. Tips (also see pictures): • Determine how high to mount the rack by measuring and eyeballing your largest bike - lift it up off the ground as far as you want it to be and take note of the top of the front tire. The bottom of the rack should be mounted between 3 - 6 inches below the top of the front tire. My wall is unfinished, so I used the 3-inch approximation (no, I did not measure - just eyeballed). • Once you mark the desired mounting position/height, use a level to draw a line on two studs. Place the rack on the line and center it between the studs. Use the rack as a template to mark the screw position. • See how close to the edge the screw holes are? Yeah, that's my biggest complaint with this product - it needs to be about an inch wider for standard wall stud mounting. Make sure to pre-drill those holes to ensure screws are driven in straight and the studs do not split! • Once the rack is mounted, pop two large hooks on each end as far apart as possible. • Different size bikes should be mounted side-by-side on the same rack to minimize petal & handlebar interferences. I rate this as 4 vs 5-stars because the racks are not wide enough for optimal mounting on studs, and I am somewhat concerned that bicycle weight may be pushing the design limits.

Put this rack up in our shed and it saves so much space!! Good quality and easy to install.

These worked so great! I took some wood and secured it to some studs in the garage wall. And then screwed each bracket to the piece of wood. Each bracket holds two bikes. Completely secure and won’t pull out of the wall.

Not as sturdy as i hoped but it will get the job done. comes in 3 sections. Plan on spacijng the sections apart quite a bit to fit bicycles in. Otherwise you iwll have to remove bicycles in order from 1 side to the other. If you space out the sections you can select bikes from any position on the hanger.

I think that having the entire 6 bikes altogether would have been too tight, but spacing each section to separate joists worked well so far. I was able to hang at different heights to make it easier for the kids to hang their bikes. Easy install with 4 screws each section that were included. I don't have drywall hung, so I didn't need to use the mollys that came with it.

I was hopeful that this would work right. But I didn't realize this was a three piece design. This would be okay if the space between all studs in every house ever was a standard size. Why couldn't they make it in one piece and then I can mount it wherever I want to, in the corner or anywhere. Probably a great product but not thought through. Suspect it to be Chinese junk.