Garage Door Torsion Springs 1.75’’(Pair) with Non-Slip Winding Bars, Coated Torsion Springs with a Minimum of 18,000 Cycles (0.207X1.75''X24'')

call any local garage door repair place and they won't sell you the springs because they claim it's too dangerous to do if you are not a professional. However, a bit of common sense and patience, it can be done pretty easily. I was glad to find these on FB and they were better priced than the local places.Install went smooth, and my garage door is back to functioning as it was before, and I'm not out hundreds of dollars for a professional to do the job for me.

Good product. Installation is harder than it appears on the videos but doable. Had to repeat the process few times to install it properly. Very first time the pulley string got caught in the door. Door got unbalanced on one side and had to unwind it and try again. After installation and trial, had to tighten a turn to balance the door in the middle. The door opener also required opening torque adjustment.Spring relaxed after a few weeks and stopped opening and then required further tightening 1/2 turn and torque adjustment. Good since then.

Great replacement spring for OEM torsion springs on grave door we had installed new 4.5 years ago. Our garage door use is very HIGH… in and out, up and down multiple times per day. As long as you measure the springs you’re replacing and get the same size you’ll be good to go. There are a bunch of YT vids explaining the process step by step. I used the one with 2M views and the young guy presenting. Very good vid. Be sure to take your time and be very methodical with the steps. As with any energized spring project this has the potential for serious injury. But… if you take your time and save the beers for after you’re finished you’ll be fine. The company who installed the garage door quoted me $345 to come out and do the work so I figured I saved over $200 by doing it myself.

Great price, fast shipping, super quality product!

It comes with instruction, easy for installation.

I have two 90 lb single-wide, 8ft wide by 7 ft tall, garage doors. I did not need a dual-spring set and only needed the right spring but could not find anyone who had a single in stock. I found this dual spring at Amazon where the price was low enough to justify purchasing. Cheaper than having a garage door service come out and replace. I will keep the left spring and use on the other garage door (flipped to the right side) when it requires replacement. I like that the tensioning bars are included with the springs. It will take several years before I can determine if these are a reliable product. This was my first time replacing a spring and I have advanced home DIY skills. I had the old spring removed and the new one installed in about an hour. If you've never replaced one before, watch a video online before install; they are easy to find. Doing it wrong can be dangerous but doesn't require a specialist to perform. I do not recommend if you don't have DIY skills. Make sure you order the proper spring. Measure your spring and match exactly. If you want a longer lasting spring you can increase the wire diameter along with a length increase to increase it's expected life. There are websites that assist in calculating the exact spring needed.There are 4 important parameters. 1) the direction of the wind although with a dual spring install you need both right-hand wind (goes on the left side) and left-hand wind (goes on the right side). The right-hand wind usually has the cone painted red. 2) the inside spring diameter, these are 1.75 inches. 3) The wire size or wire diameter which can be measured with calipers or by measuring the length of 10 coils and dividing the result by 10. These springs are 0.207" and 4) The length of the spring. Make this measurement on the broken spring or a spring not wound under tension. The spring grows in length as it's wound under tension. These springs are 24" in length. A longer spring provides less up force while a shorter spring provides more up force given that they are all wound to a fixed number of revolutions. If your lucky, some springs have all these markings on them and no measurements are required. I wasn't so lucky.Watch an online video or 2 before installing and take note of all safety tips. Be smart and be safe. Call a professional if your not comfortable installing.

Great quality, fit perfectly, works very well.

This product arrived quickly and complete. Instructions were clear and concise enough to understand. Recommend watching videos a couple of times if you haven't attempted this replacement before and TAKE YOUR TIME. Make sure you understand what measurements are needed to insure you are ordering the correct replacement. Saved at least $250 doing this and it cost me 45 min of my time. I call that a WIN!

The workmanship seems to be very good. The 7-foot-high garage door turned 31 times. It can accurately pull the garage door to the 5-foot high position and then stop. I hope this product can be like my original garage door spring， the same use for 20 years or more.

修理に使いました。海外製品なのでなかなか見つけにくいのですが、とても良い取り引きでした。

You better know what you are doing to install these but the kit itself is great.The torsion bars sure make it a lot easier and safer to install.

Product was excellent,

I like a new product and quality.