F FIERCE CYCLE2 Inch Motorcycle Gas Tank Rising Lift Kit Replacement Steel for Harley-Davidson Dyna

No instructions come with package, but can be figured out fairly easily. Install took about 30 minutes

Love how this 1.5 lift fit my 2007 Ultra.Fit form and function perfectly. Quality paint and hardware. Top cabin, Blends into frame, you can hardly notice it.

Admittedly, I bought this because I needed a 1in spacer for a front fairing, not a tank lift. But... the threads are REALLY crooked, which I just cant picture being right for any application other than allowing slop with a rubber bushing. The threads are clean enough. Screws don't spin in with your fingers, but don't take a LOT of effort with tools.The plate is nice and sturdy, its not going to bend or twist.The coating seems very thick and glossy. Hopefully not so thick that it chips easily.

Clean

As much as I like the tank lifted I have to get the 1.5 in one's. I originally have the 2in ones amd my bars hit the tank at full lock and im uneasy about it so I'll pit on the smaller ones. Really gives the bike nicer lines from the tank down to the seat. Saddle but I love it!

I wish the bolt/screw was black to match the product, and I considered removing a star for that.I bought the 2" and the 1.5" for my Batwing. I wasn't sure the 2" would let the bars clear the tank, but they did. (my bars are pretty far forward BTW)But I was wrong about prefering the 2", and I went ahead with the 1.5" anyway. With the 1/2" rear lift I felt the 1.5" lift looked aesthetically best with regards to the way the heads showed.

was too short for my application. not fault of the mfr, however i had them on for 3 months are they are beginning to rust.

I installed these on my 2020 Harley Road king. I was hoping this would make my bike would run a little cooler but haven't noticed any significant change. However, it does in my opinion look a little better. Parts fit fine. FYI, it's about a 15/20 minute job to install. Very easy!

They come with 5mm, hex head chrome bolts and washers. The brackets seem fairly sturdy. If I encounter any issues, I'll be sure to provide an update. The bracket bottoms have unthreaded holes and you use the stock bolts to attach them to the frame. The top ends are threaded to accept the supplied bolts which go through the tabs on the tank. Top of the bracket goes to the inside of the tank tabs. Easy to install although it was a bit tricky on my Road Glide. There is limited space to work because the fixed fairing does not turn out of the way to expose the side of the tank. I made sure my tank was pretty well empty. Made lifting and adjusting much easier. Remove the front tank bolts and loosen the rear bolts. I found that installing them to the frame first was easier but suit yourself. I also installed 3/16 aluminum spacers under the rear tank bolts as well. That's not necessary...it was just something I wanted to do to promote more airflow under the tank. Once everything is installed...make sure you properly tighten everything... These may cause your gauge to read a bit differently so be prepared for that. It's now easier to get under the tank to clean the cylinder heads and the extra visible chrome looks nice. I watched a number of YouTube videos and raising the tank does tend to promote some engine cooling, which on a Harley, is always a good thing!

Lifts the tank 1.5" Paint and quality seem pretty decent. Bolts are good also. Win win....compared to name brand at higher price!

I'm sure it fits the 48 and sportster models, but one set of holes need to be drilled wider to fit the Softail Street Bob bots.Good value for money mod, makes a large difference to the look and no one can put their finger on why it looks better than stock until you tell them! :)

Product is well made with good coating of paint, but will not fit dyna street bob as the bend is in the wrong place and catches on tank mounting tab. I will be keeping item as I can use it elsewhere

They fit perfectly on a Sportster and lift the tank as advertised