Question 1

will this last on a kayak?

Accepted Answer

It should as it’s lasted quite well on my truck...

But that’s just like, my opinion, man.

Question 2

How to apply?? Or is the a video you can send please?

Accepted Answer

Each order comes with a detailed instruction sheet for easy application.
Below are the instructions:

Installation Instructions:
Caution: The Adhesive used on these decals is very strong and intended for permanent installation. Once the decal has been applied, it cannot be removed without destroying it.
Preparation:
Choose the location for your decal carefully – avoid windshield wipers or areas where the decal may be damaged.
Clean and dry the surface thoroughly using RUBBING ALCOHOL to remove all traces of dirt or wax.
(It’s recommended that decals be applied when the temperature is between 45o and 80o. Before beginning, rub the sticker to ensure that the transfer tape is properly adhered to the decal.
Installation:
1. Lay the clear transfer tape side of the decal, face-down on flat surface. Carefully remove the backing paper liner, watching to make sure all parts of the decal stay on the application tape. (If they don’t, just press that part down with your thumb) Take care not to let the decal fold over on itself or touch any surfaces (A couple of fingerprints will not hurt the adhesion)
2. Carefully place the decal in the desired location. Keep the decal as flat as possible during application to avoid wrinkles and air bubbles. Use a squeegee or credit card to press the decal into place, working from the center outward.
3. Once the decal has been applied, go over it several times with a squeegee (credit card) to ensure it is completely pressed into place.
4. Carefully remove the transfer tape, starting at one corner and working toward the opposite corner. If the decal begins to lift with the transfer tape, carefully press it back into place and go over it with the squeegee.

Question 3

How do I remove vinyl Abide decal from car paint?

Accepted Answer

There are several ways to successfully remove a vinyl decal from the body of a car.  The easiest one is:Step 1: Wash the area thoroughly. Use soapy water to wash the decal area. ...Step 2: Apply Heat. Apply heat with a hairdryer. ...Step 3: Peel. Carefully peel the decal off using your fingernail. ...Step 4: Glue Removal. Apply Goo Gone to a microfiber cloth. ...Step 5: Wash.The next is:The simplest method for removing vinyl graphics is to pull them off. Of course that's easier said than done so there are tools designed to help you get under the corner of the graphic. The most common and affordable of these are plastic razor blades and "Li'l Chizlers". Both are thin, plastic hand tools designed to slide under the edge of the vinyl and scrape it away from the surface without damaging the substrate. If you can pry the edges up with a Lil Chizler or plastic razor blade, you may be able to simply peel the rest by hand. This will depend on the age and type of vinyl.The younger or more pliable it is, the better your chances of getting it off in large sections; or at least, entire letters. The older it is, the more likely it will be brittle and come off in little pieces. Long term UV exposure eventually bakes all the plasticizers out of the face film.  Here's a quick tip. If the vinyl is old and brittle, you may be able to get it to come off more smoothly by using a heat gun to warm the face film. This will also help soften the adhesive underneath and reduce the amount of work required to clean the substrate. If you live in a warm enough climate, and you're removing vinyl from a vehicle, you can opt for the original `heat gun' and just park it in the sun for a while.  You may need to use a residue remover like goo gone to remove any lingering adhesive.Thanks for your question!Roxxor

Brand	ROXXOR Decals
Color	White
Theme	Anime
Cartoon Character	American
Special Feature	Single use
Number of Pieces	1
Age Range (Description)	Adult
Reusability	Single Use
Pattern	Letter Print
Unit Count	1 Count
Finish Type	Powder coated
League	ncaa
Manufacturer	ROXXOR Decals
Item Weight	2.39 ounces
Package Dimensions	5.16 x 3.58 x 0.28 inches
Item model number	A-0071
Is Discontinued By Manufacturer	No
Manufacturer Part Number	A-0071
Special Features	Single use

ROXXOR Decals The Dude - Abide - Precision-Cut Vinyl Decal/Sticker

Description

Specifications

Have a Question? See What Others Asked

Common Questions