Spoiler Wing Compatible with 2017-2023 Tesla Model 3 Spoiler Wing Sports Cars Rear Spoiler Car Styling Kits Tesla Model 3 Accessories (Matte Carbon Fiber Pattern)

Gloss black spoiler matches my black paint perfectly. It’s not a perfect fit to the profile of the car, but it’s very close. Body pieces rarely are perfect.There’s one major concern you need to be aware of if you want this spoiler to stay mounted for a long time… and that’s water getting under the top edge. This spoiler creates a pool of water with how much it slopes up. Any water that runs down the back part of the car will just sit and cause problems for adhesive tape. I doubt it would last 3 months before the edges start pulling up.The solution: use a sealant to keep the water out. I used DAP ultra clear silicone adhesive caulking. It’s a product I’m familiar with that tolerates moisture and temps. I think it turned out nice- and you can barely see it. It will also help hold the spoiler in place. You could use marine sealant or RTV gasket maker alternatively. I sealed around the top edge and around the corners. No water can penetrate under the spoiler now.

This spoiler is beautiful! It added pizzaz to my 2019 Tesla Model 3! We used masking tape to mark the center of the trunk and the two side margins to make sure it was installed and centered properly! Note that once the tape touches the car, it is pretty difficult to move again -- so, patience is the name of the game when installing this spoiler. It is very secure -- will probably be on my car forever based on how it is adhering today. After I installed it, I sat my car in the hot sun for a few hours to make sure the advesive took hold. It is a beautiful addition to my Tesla! I recommend this product!

I should have taken pictures. On each side of this rear spoiler, there is 1 hole underneath between the tape and the spoiler. For whatever reason these two holes were huge convex bumps. Think of them as large boils one might get in their skin. There were so bad that there was zero chance of this sitting flush on the trunk and it would only have tape contact on the middle portion and where the 2 holes protruded out. This surface need to be FLAT. It was crazyI really didn't feel like sending it back and ordering from a different company. what I had to do was remove tape from the not level areas and use a Dremel to make the area flat. Then I used my own 3m vhb tape over the area I made flat. By the way, they don't use 3m tape. But they do provide adhesive promoter wipes that I did use.After test fitting it appeared that it would sit flush and not have huge areas of gap like it had. I've built commercial airplanes for many years so I know how parts need to fit together to be successful.The carbon fiber glossy print doesn't look bad. There were some scratches on the top surface but I think they will polish out. And I'll ceramic coat it to help with future possible scratches and uv degradation.It was packaged nicely in bubble wrap and a cardbord box. No instruction for install but there are many YouTube videos on this type of stuff

Looks really nice and the installation was easy. However, one of the sides was unstuck less than a week later. I know most would say that it was due to a bad install, but it wasn't; not my first time doing this. I cleaned the surface beforehand, got help while installing, and made sure that it was properly done before securing/weighing it down for a few hours after installing. Then, I did not drive the car for a couple of days after the installation and even covered it in case it rained.The finish is good, but I hope it lasts long. The last one I bought from a different seller started pealing off around 6 months later - not acceptable.

Just installed I’ll need a few weeks/months to verify quality but it fits well and looks nice. A little bigger than I thought but that’s just me. Good value for price and installation was easy. Adhesive was good and I didn’t have to add additional tape.Ensure your measure and prep prior to install. Be mindful this sits on top of the trunk lip vs the performance factory that wraps and hugs the trunk lip.

Just installed today and looks absolutely phenomenal! As long as the adhesion holds up (I have no doubts that it will, its already on there really good) would 100% recommend for anyone that doesn't live near me! (Don't want everyone in my area to end up with the same spoiler on their Teslas hahaha)

It was a very quick install to do by myself. I added some extra 3M tape for insurance and used masking tape to make location guides before removing the adhesive back of the 3M tape.

I wish I would have return this Spoiler wing for my Model 3 Tesla 2023 sooner. Within 6 moths the carbon spoiler fated and now it looks really bad. Worry to take it off cause it might mess up the car paint. This product is NOT good at all