Oracle Lighting 5874-504: Rear Bumper Led Reverse Lights For Jeep Wrangler Jl

They are worth the money and are a great solution to the factory back up lights. It’s not that easy of an install and taking the Bumper off is the only way to go. I installed them on a 2020 Jeep Wrangler JL 4 Door Rubicon. I saw one seller say it was a hour install and that my friend is not possible and I bought the Plug & Play wiring harness which is the way to go and it’s around $38. Both of my lights fit perfectly without any sanding or grinding. Hope this helps somebody with their install.

Great quality and bright. Easy to install once I removed the rear bumper to access the 7mm reflector bolts. great look, function as expected.

Giving 5 stars because they definitely help with visibility. Passenger side installed with ease. Ended up breaking the lense on the driver side during install due to poor fit. After some research it’s a common issue when installing on the driver side so be careful.

Wonderful lights....really bright, they make all the difference in the world when backing up....... But...... They are IMPOSSIBLE to install on the 25 JL without removing the bumper. Read the instructions, watch online YouTube videos, try all you want, but the bumper has to come off. If you have a trailer hitch, that comes off to remove the bumper. Not just me.....I took these to a Jeep specialty dealer....they thought 2 hours.....it took two guys six hours to remove the bumper, install the lights (minutes), and but the bumper back on. I love them, but beware!

When installing these aluminum houses lights, I had to pound the passenger light into the bumper to get it to fit. The driver’s side? Not a chance. I had to pull out a dremel grinding wheel and spend about 15-20 minutes grinding away the aluminum housing at the upper/inner corner and the whole left side, followed by pounding with a fist to get it to fit inside the steel bumper. I figure aluminum is less likely to corrode as grinding away the steel bumper. Not the best fit. I would expect a better fitting product from Oracle. Once I got the back-up housings installed, I used the factory screws to hold them in place. The screws are then too long. I kept tightening the drivers side. It snapped before it got flushed. I tightened the passenger side until it got tight. If I run into problems wiring or getting them to work, will post another review. Not cool Oracle… Tom

Install is a little tricky (it was easiest to remove the rear bumper) but they look good and are very bright. I wish they lit a wider area...the beam is fairly narrow but it's a huge improvement over the terrible factory reverse lights. I bought the wiring harness from Oracle also and it made hooking them up a breeze.

I really like the output and overall build quality of these lights — once they’re finally installed, they perform exactly as advertised. Bright, clean beam pattern, solid housing, and they look great on the vehicle. The problem is the installation if you’re running a steel bumper. There’s almost no clearance to work with, and the mounting hardware becomes a fight from the moment you start. What should be a straightforward job turns into a time‑consuming, awkward process of trying to get tools into spaces that simply aren’t designed for them. If you have a plastic bumper, you’ll probably never notice this. With a steel bumper, expect a struggle. Bottom line: excellent lights, but the install is far from plug‑and‑play if you have a steel bumper. If you’re prepared for that, you’ll be happy with the end result.

Great additional reverse lights for the wrangler. I love mine. I have a 2024 392 Rubicon and saw some reviews said they don’t fit so was hesitant. But I had a shop install them and they said one fit fine the other just needed some sanding. I had windows tinted dark and these really help light up when reversing and they look great. 10/10

All good, the lights ok with Robicon 4xe JL.

Après plus d'un an, fonctionne toujours a merveille et nous avons l'hiver avec la gadoue et le sel de déglaçage, je recommande!

Good lights give off descent light Much better than stock Very difficult to install without removing bumper My issue is I wonder how the unprotected wires will resist over years to road salt etc

Fit perfectly in my OEM Plastic Bumper, however when installing them on a OEM steel bumper the Driver Side light requires some shaving to fit