AUTOXBERT 38cm/15 Inch Hand Sewing Steering Wheel Cover Breathable Anti-Slip Leather Steering Wheel Cover for Qashqai Toyota Camry RAV4 VW Golf

great fit, not too tight on a fiat panda (04) steering wheel. did not sew through the stitching but used blunt leather needles and sewed through the holes on the edge of the cover. used two needles, thread cord and put through 2 adjacent holes from the outside in, carry on round the wheel and pull tight and tie off when you get to a spoke( an assistants finger helps, like tying a bow) sew through the holes past the spoke , outside to in on the first pair of holes and pull tight and tie off, carry on sewing like this all the way round. pull tight til the edges nearly meet and the thread makes a very good seam and excellent grip on the cover. looks great and the grip is improved no end, perfect for older cars. sewing like this is a lot harder than some covers state but the end result is more professional and less likely to go wrong. just take your time and it does work.

Instructions could be better BUT it was easy to fit, looks great an feels surprisingly quality in the hand, the leather is soft, supple and strong 💪

Nice look and easy to fit it. Took me about 30 minutes to do it but I like the final result. It doesn’t really feel like a genuine leather but will see after couple of months if is a original leather or PU leather. More than enough Thread but slightly different colour. I see some reviews saying that not enough thread but you need to connect the STITCHES tougher from both side only so one meter should be enough and do not double it for no reason as the thread is very strong. Only 4 stars as it doesn’t look genuine leather but seems to be strong anyway

My wife wanted this for her car, and according to her, it was fairly simple to do, and it looks amazing. She also says the steering wheel feels so much better now.

Be very careful received product looked like reject. No needle or threads. Stich was out Would never buy from this seller. Package came like used bag.crap quality.

Nice product, but NOT LEATHER!!

It fits, it's easy to lace up, it looks good.

Perfect fit for my steering wheel as per the measurements in the product description. Plenty length of ‘yarn’ supplied to stitch all way round, and needle included as well. I stitched through the holes in the leather that the edge stitching goes through, rather than try to catch the edge stitching as the instructions seem to suggest. My old foam steering wheel was starting to wear in places and this cover makes it look better than new. The soft leather is really comfortable and doesn’t slip on the wheel or in my hands. Its for a specific sized steering wheel so make sure you measure before buying.

Ich bin sehr sehr zufrieden das Produkt ist fein gemacht und man kann das selber an den Lenkrad bringen. Ich empfehle jeden wenn sowas braucht zu kaufen.

Installed this steering wheel cover in my 2015 Mustang. It took me about three hours over a couple of days (had some interruptions). I had plenty of thread with about three feet left over from one of the two bundles of thread. The extra allowed me to separately stitch and tighten the material around two the the three steering wheel spokes. If the spokes were smaller the cover would look better. I like the feel of the cover so far and it adds just a bit to the diameter of the steering wheel which I also like. The slip on covers that you don’t have to lace are too big in my opinion. I looked online at videos and found what seemed to be the most common stitching method. It was fairly simple. Just had to remember to go from outside the wheel to the inside on each loop. I did get it wrapped around the wheel a couple of times when first starting out. I did find that o could run about ten or twelve stitches and then go back over what I had just done and tighten each stitch a little more pretty much closing the gap. I initially just ran the thread under the cover on the backside of the two wheel spokes. However after I was done I didn’t like the look. I ended up cutting the thread on the backside of the spokes and started a new stitch and working away from the spoke, removing previous stitching as needed. I was able to secure the ends in a knot keeping it taught. Only time will tell for the quality of the leather cover and its overall durability. It’s a lot softer to the touch and more comfortable than the stock plastic-feeling steering wheel. It was an easy installation that just took time to lace it up, keep it straight and tight.

Fits really well, takes about 1-2 hrs to thread on depending on your thread and needle skill… I learned to thread the needle into the outer loop then straight through the inner loop (then pull the string all the way to tighten) : think about it like threading ur shoe laces, and dont pull it too ahrd otherwise it could snap, however the leather is really strong! Great product I love it! Very slim material and a snug fit onto the original steering wheel- a lot better than buying a cover from auto stores that cost triple the price and are thick and looks worse. ( Toyota Corolla 2019 Ascent Sport)

This fit very well on my Hilux steering wheel. Nice and thin, so it is a good repair when your steering wheel starts to peel. Advice is when you are stitching it on. Start at the seem, so it lines up when you complete your way around the wheel. Be prepared for slow repetitive sewing to get it on and to make sure to keep your stitching tight. If you do, it is a nice feeling cover and none of the stitching pulled through the fabric.

Installed this on a 2022 Lexus RC, and the red stitching matches the car’s red interior really well. The Australian sun can be hard on steering wheels, so we wanted a sacrificial cover. The kit includes plenty of thread, and the cover fits tightly once in place. Installation is a bit time-consuming at around 1.5 hours, but the result looks clean and factory-like. Overall, we’re very happy with the finish and feel of the material. We recommend it to anyone wanting to protect their OEM wheel.