Set of 2 Studio Monitor Stands Desk Clamp Desktop Speaker Stands with Isolation Pads

I wanted to get my Polk S15 speakers off my desk so they could be ear level and also open up some desk top space so it would feel less cluttered and these stands did that job perfectly.They're very stable. Even if I shake the desk a bit the stands have very minimal wobble they just move with the desk for the most part despite being so top heavy with these big speakers so the stand clamps very nice and firmly and the pipe portion stays tight. So when using my mouse and keyboard while gaming or coding I don't have to see them wobble in my peripheral vision.They assemble very easy with pretty much no need for instructions. I glimpsed at the instructions but I already put two and two together. Same bolt for the top speaker plate and bottom clamp so there's very little to figure out.The quality is very solid too and the padding on the speaker plate is a nice touch to reduce vibration and helps keep the sound coming from the speaker instead of the stand.Also the speaker height is very easily adjustable which is nice. Hand turn a knob and lift the speaker plate up then tighten it and you're done.Some issues I have with the stands:1- there's no real clean way to run the speaker wire without bringing in 3rd party cable management products. I wish they had a hole at the top and bottom of the pipe that holds the speaker up so you can run a cable through it or even better if they put holes down the back side of the pipe with little "wire guiding" clips. Right now my speaker wire just hangs off the back while I figure out a cleaner way to run the wire down. Probably will use some small adhesive clips so it should be a cheap and easy fix and is mostly a non-issue but for the cost, simplicity, and purpose of this product you'd expect a better way to do this as part of the design. Oh well. Not that big of a deal.My second issue is that one of the bolts it came with had a manufacturing defect where you put the hex tool into it to tighten it. It has a warped or almost smeared metal look to the inside of it making it impossible to properly tighten the bolt all the way. With some heavy pressure and slow turning I was able to tighten it enough to keep the plate from loosely rotating though it still is pretty loose compared to the other stand unfortunately. Oh well, I'll figure out the threading and buy one at my local hardware store. Annoying and easily avoidable if they just threw in an extra bolt. Can't imagine it would add more than a nickel to their cost considering even the cheapest products I've bought on Amazon like this almost always come with an extra screw or bolt just in case.All in all I love this and highly recommend it if you want to lift your speakers off your desk. It looks great and made my desktop workspace much more usable and less crowded. Not to mention, the audio sounds much better now that it's ear level and not sending sound below my head.Final note: please ignore the mess in my office after I just complained about no easy way to run the wire in a clean way. I just built my desk and I'm still in the process of doing cable management and organizing!

Exactly as described, very easy to assemble and very heavy duty.

These speaker stands are great, sturdy, and easy to assemble. The foam is nice and I don't worry about anything. We'll see how they hold up over time. I'm only giving 4 stars because they're too high, and I feel that, as a desk stand, they should not need to go as high as they do. At the lowest setting, they are above my ears which I'm unhappy with. Thus the speaker placement and sound isn't as ideal as I'd like.

I got these to finally get my PreSonus Eris 8' monitors off the desk and to a more consistent spot to be able to feel more confident with EQing and mixing. I was a little hesitant as I wasn't sure these would be sturdy enough to hold an 8' monitor. I got them set up within 5 minutes and have nothing bad to say about these. I would install them by evenly screwing in the clamps, put your monitor on, and then reset the clamps to make sure there is no way. If you set them up haphazardly you might end up with stands that are a little loose. Just spend an extra minute after initially tightening them to add your monitor, apply a tiny amount of tension in a 360 direction, and continue to hand tighten until they don't have any swing or give in them. Hand tightening should be plenty. Great product for a ridiculous price.

So good! VERY sturdy, fits my montoris great, and even has options to hollow out the middle of the pillar to slide the chords through

I bought these for my Kali LP-6's. They're nice stands, but they're struggling to support them. I've adjust and tightened screws a few times, and after just a few hours they're already starting to look lopsided and needs to be tightened up again. The Kali's are only 15lbs a piece, no way would I trust these to hold anything heavier. I'm probably going to return these and look for something sturdier.

My husband loves these for his monitors. They work great.

I have to very large Yamaha hs8 studio monitors that are 25 lbs. these hold up with no issue.