Black Reflective Vinyl Adhesive, 12" x 4 FT Roll by Turner Moore Edition

Super bright reflective! Ran through my cricket perfectly. I had to cut it on a higher setting because it’s pretty thick but man did it come out great! Used it to make a 9” first responder sticker for the back window of my truck and against the tinted glass it really popped! I messed up installing the first time and like with any vinyl it’s not very forgiving but let me tell you the amount of stick this stuff has is second to none. Had to scrape it with a razor just to get it off so I could put the second one on. Survives Minnesota winters stuck to the glass! Buy it now!

Good value for the money, easy to cut and apply. It’s reflective for mining hard hats. Black that turns gold under light

5 stars for now. Used Maker 3 to cut. Saw several reviews that 190 pressure wasn't quite enough. I used 200 and it was a little too much pressure, but workable. I put it on the back of HD saddle bags. Looks great. Will see how long it lasts and may review again then. I recommend getting it lined up and use excess transfer tape to keep in place. Peel backing off just an edge (like 1 mm) and stick it down. Make sure it is lined up, if not, you can easily lift it to move it. Then burnish and the backing will come off as you burnish. This prevents bubbles. This material is very stretchy.

This vinyl does work, but I had some issues at first. I've only used my Cricut for decals once. I usually make tshirts, so I had to use some trial and error. I was actualy so disappointed with this product at first, I was going to give it a bad review. I'm glad I gave it a second chance. I decided to read some reviews and the product description again for a little guidance, and I was able to figure it out. Here are some instructions I came up with to help. * For my Cricut Explore Air 2, I set it to the dot between iron-on and light cardstock * You have to keep the shiny side up, paper side down * DO NOT reverse the image (used for iron on) * Use the weeder not to weed away the extra, but to hold the image onto the paper backing. * The weeder doesn't really work to remove the extra. You are essentially removing stickers from paper, so you can just peel it off with your fingers. But HOLD THAT IMAGE DOWN so it doesn't come up with the weeding. * Be SUPER CAREFUL not to allow the removed weeded pieces to overlap back onto the image. It's really sticky and will get stuck to your image, potentially causing damage. I cut the extra off every inch or so to prevent this from happening. * Then I used regular Cricut Transfer Tape to transfer the image. I scraped over the image really good with the Cricut scraper tool before carefully removing the tape. My project came out really nice. I'm using it on my mailbox, so time will tell if it holds up to the outdoor elements.

I wanted to make house numbers for our new mailbox before I installed it and I wanted to make them with reflective vinyl to make them easier to see at night. This roll seemed reasonable for the price. It does indeed reflect as advertised. I will attach a pic taken with the flash on. I did find it tricky to cut on my Cricut. Since it is thick, I tried first setting it to Vinyl+. That cut but not quite deep enough to cut the vinyl and adhesive and it was tough to weed. I tried a custom setting as recommended by another reviewer here with a little higher pressure and a double cut. That failed because on the second pass it would fold over the small ends of the letters. Next I tried the default Holographic Vinyl with a single cut and that worked better. Pressure was about 195 on that setting. If I have to cut this again I might bump that to about 210 or so. It loves to stick to itself so as I was weeding I kept a pair of scissors handy to snip off the excess as I peeled it up. It’s very stretchy and easy to ruin. I managed to mangle one just applying the transfer tape, my transfer tape had a bubble in it and it pulled up a number when I tried to smooth it out. That was my mistake though, not a fault of the material.

Reflective vinyl is VERY hard to use. BUT there are a few things you can do to make it doable. The material is a thin stretchy membrane that wants to re-adhere to itself even when cut, has a thin glue membrane that doesn't always cut through, is stretchy, doesn't like sticking to its backing. 1. double cut. Make a customer material that does every cut twice. Add a box around your design so you can pick the entire thing up including the box. 2. REVERSE WEED - Cut, transfer ENTIRE thing to transfer tape, put the transfer tape sticky side up on the sticky matt to weed. The transfer tape will hold things together WAY better than the carrier it comes on. Use one tool to hold down small sections when ripping away the parts you are weeding. 3. Be comfortable ripping the parts you are weeding. The material is not very strong, it is easier to do in parts by ripping the vinyl, be ok with it ripping and going back to pull up those parts.

Sorry, I've done a lot of cutting with reflective 3M vinyl, and this stuff is not good. It acts like foil, not vinyl and my cutter is not good at cutting it, especially anything small. It might be fine for larger project, though. It's also difficult to weed because it crumples like foil and easily sticks to itself, making anything like Ps, Bs or Rs a nightmare to weed if they're small. It does, however, reflect well and is true to color. It just seems to be a bit of a pain to work with compared to what I'm used to.

looks great, not sure if it'll last outside for long I guess we'll see

It worked great for what I was using it for.

I was surprised at how well this reflects. I've had stickers I made from this on my car for more than a year and it still works.

This was perfect for what I needed. After wrapping by bike with vinyl I used this material and a cricut maker to create the replacement graphics for my bike. Easy project with great results.

Really good quality, easy to apply & has stood up to torrential rain!

This product is exactly as described. So happy with my purchase.