Toilet Inlet Valve Bottom Entry, Inlet Float Valve 1/2 inch

Very good quality for the money. Delivered on time and decent price and packaging. It was very easy to install the new valve, run very silent and fill cistern in about 20 seconds. The old one needs almost 25 minutes. It took me ages to get out the old valve and bolts between cistern and toilet but that have nothing to do with this item . I found very easy to set water level by unclip the plastic stopper and twist the body then extended to the desired length. Very happy with the result despite I am not a DIY warrior and saved big money for the plumber. Time will tell how long will last but for now looking good and build quality is excellent for the price. The brass thread is very useful.

Does the job. Installed for a low water pressure system. Filling rate is not very fast, but it never was really. Probably not caused by the inlet valve. Make sure the filter stays in place when installing. Mine dropped out and I only noticed too late after installing and couldn't be bothered..... At first i thought the inlet valve wasn't working, as it didn't shut off the water fully which caused it to overflow eventually. But it turned out with the assembly I had dislodged some debris which came in the valve. The manual states to regularly clean the filter... but that's never going to happen as it's too much effort to remove it again. Instead the top can be removed, pull the pin out and carefully remove the lever mechanism. Then the centre piece can be pulled out with the valve. Any debris there will prevent it to fully close off the water supply. Just clean it and re-assemble. There's another review which suggests to remove the rubber that sits below the plastic inner piece - which can be pulled out with pliers ( careful not to damage the edges the valve sits on to close the water supply) - to improve water flow..... However that rubber turns out to be essential ( in a low pressure system) removing this rubber does somewhat improve waterflow BUT without it the valve stays closed and only by tapping the mechanism it opens.

Thing of a beauty, a joy forever. Super easy to install, fits into the tiniest of spaces. I left the old flushing mechanism in the tank and just replaced the old cock and ball valve with this. It's quiet and fills up the 8 litre tank in under 30 seconds. (Compared to the 3 minutes before) Just make sure to twist the shaft and set the top of the blue plastic (critical level) to the height of the syphon's overflow. Then twist to lock again and insert the small plastic piece back to secure the position. Before installing the mains water, be sure to remove the piece of plastic from inside the 1/2" brass inlet at the bottom. Took me no time to install, no leaks or noise. ------------------------------------------------------------------------------------------------ UPDATE: After a week, it stopped shutting down completely and the excess water is now leaking into the bowl. Buying a Fluidmaster instead.... ------------------------------------------------------------------------------------------------ UPDATE UPDATE: After another week, it started working perfectly. No leaks or overflow. So in the end I kept it. I don't know why it had a hiccup but it gets plenty of use and has no problems.

As someone who had never changed a toilet inlet valve before, I found this remarkably easy to use, and it saved me a significant amount of money that I otherwise would have paid a professional plumber. Because it is a bottom connector, it did take a little time and maneuvering to reach the nuts underneath (as you can see in the photo), but the actual installation process was completely straightforward. The valve is highly adaptable and incredibly durable. You can effortlessly twist the main body to elongate or shorten the height to match your siphon, and adjusting the exact amount of water that fills the tank is very simple. The absolute best part is the solid brass connector. Cheaper brands often use plastic threads that can easily break or cross-thread under pressure, but this brass fitting gives you complete peace of mind and feels extremely safe when tightening the water hose. I am very happy with how solid and hassle-free this fix turned out to be.

My family were getting annoyed with flushing as the old Eco valve would take 25 minutes to fill up! I did some research on Amazon reviews and picked VeeBath toilet inlet valve bottom entry. It was relatively straight-forward to install. Some tips: get a small container and towels to soak up any leakage. Drain the tank completely and turn off the isolation valve to stop water getting in. Take out the old inlet valve by unscrewing at the bottom of the tank. Before inserting the new VeeBath toilet inlet valve, ensure height is 3cm above the outlet pipe. Once installed, it would be almost impossible to adjust the height. Once it's installed, there is no need to over tighten the screws on the inlet valve. Get the towels and container ready and turn the isolation valve back on. Hopefully, there is no leakage. If there is any, it may be necessary to change the washers. Also, it's rather quiet filling up unless you are ultra sensitive to pin-prick decibels. Now, my family are pleased with the quick refill as it would only take 2 minutes compared to 25 minutes for the old Eco valve. I would certainly highly recommend Veebath toilet inlet valve bottom entry.

I bought this particular style of valve to replace an old style ball arm type as part of a complete refurbishment of the bodge up from hell (see photo) . The new valve now sits in splendid isolation on the left hand side of the cistern with the water inlet changed to suit and the previous right side entry hole blanked off. Initially I looked at other valves costing twice as much and thought that perhaps this one wouldn’t be so good but went ahead and bought it anyway. Surprisingly it is pretty well made and is supplied with a decent idiot proof cone shaped rubber sealing washer. Not sure if the stem is actually brass or brass finish . Hopefully it is plated copper and not DinkyToy alloy . The instructions are pretty basic and do not explain fully how to adjust the height of the stem . This is done by twisting and unlocking , sliding to size and then twisting back to lock and is probably best done before fitting. Only grip the shaft when twisting as the working parts are less robust and will probably break off. The packaging says it’s designed in the UK and made in China (what isn’t) . Anyway if it’s as good as my I-Pad I won’t worry. The inlet is fitted with a removable filter with regular cleaning advised so I suspect this and others of the type are susceptible to dirt or debris so perhaps worth paying attention to . The metal connection , unlike plastic should stand up to routine maintenance . Suitable for low and high pressure without the need for restriction inserts and on my 3 bar mains fills in seconds and is particularly quiet, unlike its predecessor mimicking a hose pipe filling a bucket and dripping encore. Instructions do not include any reference to dismantling the top end for washer replacement etc , but considering you might have to pay £3-4 for the washer alone what would be the point, better to get another valve .

This was my first time doing any sort of plumbing. Easy to put in and secure so it didn’t leak. Still working after a few months, so happy

This was the cheapest option I could find but worked well. Although it felt slightly cheap and was fiddly, I did manage to fit myself and it worked successfully. I am not a plumber, nor am I very practical, and although it took a couple of hours, I did manage to get it to work without any leaks. From memory, there weren't any instructions, or certainly they weren't that useful, but was able to resolve with a couple of YouTube videos. One of the positives is that it fills quickly and quietly. Overall positive and I would probably purchase again if I needed another.

Système de remplissage silencieux

Funziona a dovere

Really good easy exchange for the 10 year old one in the toilet very easy to adjust just a slight twist of the top and the you can lower or raise the water level the main bonus it’s so quiet when filling I had to check several times to see I had put the water back on very pleased the other good thing is the brass fitting on the end made it easier to tighten without the risk of stripping a nylon thread like done cheaper models

Funktioniert zu 100%. Mehr als hervorragende Funktion geht nicht!

Bon matériel