HOBBYWING Quicrun Fusion SE 540 Spec (Fusion SE 1800KV)

I have 3 or 4 different fusions in my crawlers and I can't have anything else. Especially this SE is a great value, for being a sensored brushless motor, esc, and a built in 4Amp BEC, while being all sealed and waterproof. If this is your first Fusion, or Hobbywing product, know that it doesn't come with a programming card. You will need one to set it up, or borrow from a friend in the hobby. Then just enjoy this very powerfull, smooth and quiet setup. I know I am, and I will be back for more. Quality, performance, direct fit, pwerfull and clean installation with minimal wiring by having built-in ESC and BEC.

Works amazing in my vanquish vrd stance. Good power and capability. Would highly recommend this motor/esc combo to anyone looking to get a brushless motor. Fit great but didn’t come with screws to mount.

Awesome product works so much better than the stock motor in my crawlers. Definitely takes your crawler to better level the slow speed control is night and day . So much better than stock. The 2in 1 is definitely nice and cuts back on the wire mess of having a separate esc/motor. I have put them in all my crawlers. They just work flawlessly for me

Super smooth and well made motor, the 2 in 1 combo is amazing for saving space and weight, I have this one in my Element enduro trailrunner and the Fusion pro in my gen 8, and both are amazing.

Well like I said I'm a hobby wing fan I have not ever had a complaint about any product I've got from them until now, Which ain't necessarily hobby wings fault either but I received my 1800 KV quick run fusion SE and I noticed the shaft was slightly bent, I couldn't see it by my eye it was when I was putting the spur on against the pinion I noticed it and I figured id try to run it anyways so i got the rig back together and headed out front ( Just a normal yard no crawler course just grass grassy hills in a subdivision nothing crazy) for the first round maybe 15-25, And it was obnoxiously loud which irritated me because my buddy across the street has the same motor, its why I ordered this one because of how quiet was and of course the low end torque. 1525 at the most minutes and the shaft snapped off at the base of the motor housing, Like all of a sudden just stopped rolling I was like what the **** and it was you know so quiet I couldn't hear nothing so I thought it was burnt honestly, What is that got close to I can hear the motor spinning when i Bumped the throttle I was like alright so spur came off didn't tighten the grubs contain that so I'm looking down there i'm looking for a gear and I'm looking I'm looking I'm like it took me a couple minutes to realize that I was what I was seeing no motor shaft and lost my Favorite Lucky 20t spur That I've carried through a few rigs along with it so can you see about a replacement I hope they don't make me do a refund and then rebuy I just want a replacement straight across Look as minimal lag time as possible so I can get out some crawlin, the job side I'm workin on right now is perfect so we'll see. Anyhow short story long I will not knock having you i'll chocolate up to mishandling and shipping or something else let's see every RCI have is hoping in power I have several from 1/10 Crawlers and bashers up to my fifth scale DBXLE 2.0 SCX 6, oh and I do have A TRX4m as well TRX 4 sport, The motor in question is on an SCX10 2 anywhosit carry on happy crawlin, I'm 47 and I've been playing with RCS since Tyco RC Bandit and the grasshopper that it was? oh well. I'm sure it's just a fluke hey if y'all read this seller amazon how are you in y'all wanna send me some new gears as well thank you 20t Figured two or three of them maybe 4 or should replace my lucky 20 T that is now lost forever it's been with me for heck a couple years few years three rigs lol Okay the trees got ahold of me and I'm rambling I'm out of LMAO.

The 2 in 1 fusion SE was better than I thought it would be. Very smooth, low end torque is unbeatable! Will be ordering 2 more for other RC vehicles!

The Fusion SE and Fusion Pro are my go to in all my crawlers. Super easy to install and the esc settings can be customized with a programming card. I think I have purchased 5 of these and have yet to have a single issue.

This motor is so good that it gave my truck enough wheel speed and probably a little bit more than the stock motor and has extreme torque to make your truck climb over stuff, the drag brake is why I purchased this motor and completely satisfied with it, sure the 1800kv motor is probably more ideal for a lot of people but the 1200kv is good enough for what I need and the run time last a little bit longer than the 1800kv but for crawling it's not a race truck so this one is fine, was easy to install, easy to setup and if you have the program card you can find tune it for some stuff just not like the fusion pro 2300kv

very quiet motor! l love the way it crawl walk!!! Best for its value. highly recommended!!

Just buy it, these things are awesome. Crawling perfection. If you want a bit more speed, grab the 2300kv version.

We have upgraded two of our machines (both around 17 years old, used machines given to us) with the Fusion SE motors. What a difference in low speed. Our old motors were jerky to start and didn't have much brake for hill stops. These new motors are wild for how slow you can move, and the throttle comes on slowly, so there are no more jump starts. The braking is great too. We would have to hold the machine in the opposite direction while stopping on a hill. Now, we can stop, and the motor holds it still. We were able to clean up the wiring as we no longer need a separate ESC, giving us more to run the electronics under the hood of our Jepp. The one thing we didn't know, as we are new to this part of the hobby, is that we should have bought a LED programming board with the motors (we have ordered one now). The stock settings are okay, but we need to switch the rotation direction (we have it changed on our remote right now) and would like to play with the brake settings.

The excellent reviews that it has only begins to explain just how impressive this esc motor combo works. I installed in a trx4. The installation was simple and very neat. I did need to purchase a hobbywing programming card to adjust the motor direction. That also was very easy and explained in the included instructions. It operates almost silently and the slow crawl and smoothness is second to nothing that i have ever tried before. .

Transformed my axial scx10iii to a perfect crawler highly recommended