【𝐍𝐞𝐰 𝐕𝐞𝐫𝐬𝐢𝐨𝐧】SUNLU S2 Filament Dryer Box, Keep Filament Dry During 3D Printing, with Fan 360° All-Round Heating and 4.6" Touchscreen, FDM 3D Printer Filament Storages

Compact, easy to use. Used immediately for drying Nylon filament which is very hygroscopic.

As far as dehidrators go this is an excellent unit, does exactly what it's meant to do and does it really well. After a few weeks of use old butter fingers (me) drops the unit smashing the touch screen.I reached out to Sunlu to see if they sold replacement screens. I wasn't hopefull of even getting a reply given what I had read in some reviews, but a reply I got. They said they don't currently sell spares but they could supply a complete motherboard which included the screen. Within a matter of weeks I had a brand new motherboard arrive in the post completely free of charge, didn't even have to pay for postage! Easy to fit, took a about 10 minutes at most. So regardless of what you may read, at least in the UK, Sunlu's customer service is next level!

This filament dryer is simple to use and does a reasonable job of drying a single spool of filament. What would improve the design would be a fan to extract the moist air out of the unit and away from the filament; as it is, condensation builds up inside the unit which does not escape easily.I would recommend 3D printing one of the wedges designed to raise the lid a little to allow the wet air to escape which improves the efficiency no end.

Used for the first time recently, very easy to use. Simple features. Good value

Had the Creality one first and it was terrible so returned it and bought this.. and its brilliant..

Already Down to half a roll of the filament good service as well

I like the clear display showing time temperature and humidity. Initially confused that it wouldnt turn on but then read the instructions! I use this standardalone i.e. I do not feed the filament from the box out to my 3d printer. I find that the moisture in the heated air doesn't vent properly so every now and again I briefly open then close the lid, which almost immediately afterwards shows a reduction in humidity on the display.

Easy to use with clear display and nice easy to use touch screen interface that displays the set temperature, actual temperature, filament type as set at start, time remaining and humidity inside the unit.The unit has heaters in both the top and bottom unlike a lot of the cheaper units and the air circulation fan is nice and quiet.Overall it does what it should and is easy to use.

This is a great filament dryer. I use it almost all the time before any large print jobs and it really makes a huge difference in the quality of the prints. I also use it to dry filaments before storing them in vacuum packs. Even when filaments are just sitting in my AMS which is filled with dessicant filaments will pull some moisture from the air. For critical long prints I still pop the filament I am going to use in this. I used a temp sensor and this unit can easily hit 80C or higher. Great buy!

Gracias a este producto puedo imprimir materiales como nilons, gracias por permitirme seguir con mis proyectos

I purchased this product as an add-on to my 3d printer. I was having issues with moisture in the filament and this drier has solved that for me. I have tested it over the last few days and am very impressed with its simplicity and function. The drier is preset for specific types of filament and has defaults that work very well for the type of filament selected. After only one 6 hour cycle in the drier, the adhesion and stringing issues I was having have disappeared. I would highly recommend this item. There is nothing worse than finishing a long print to find it unusable due to filament moisture issues.

Till now anything I got related to 3d printing that I do like it is this one is been working for so long and still so good.RECOMMENDED

The media could not be loaded. Últimamente me han llegado muchos filamentos húmedos y además vivo en una zona con mucha humedad por lo que los filamentis que tengo desde hace tiempo siempre acaban húmedos.Es eficaz y en unas horas te ha dejado el filamento seco. Además te permite utilizarlo mientras imprimes para así asegurarte de que el filamento entra a la impresora en condiciones óptimas.