Chrome Bullet Rear LED Turn Signals, Motorcycle Brake Taillights 12V Tail Lights Compatible with Halrey Sportster 1200 883 Softail Fatboy 1990-2024

Lights are great! Took a minute to figure out how to put them on a ‘21 street Bob.You can’t use the plastic socket housing that come with these lights, so you’ll have to cut the connectors off and replace them with the namz connectors to fit in the original plastic socket housing.Start with black on black, red, yellow, and white. On my bike that was left to right.Maybe that’ll save someone some time.

Great value, very nicely put together and great quality, loving in Ireland I was worried about rain getting into them like the OEM ones that blew from filling up with water but not a drop inside the lense haven't even seen condensation and have been through hail, rain and bike stays in the garden and is ridden every day, would definitely buy again...but probably won't need to!

Install Time: 1 hour install depending on tools you have.Tools needed: 13mm wrench or socket set.Hardest part: getting fingers through hard to reach areas to losses/tighten bolts.Wiring: Wiring was not so hard the only confusing part was that the stock light are a 3 wire and these are a 4 wire. I did sever trial and error attempts on getting blinkers and break lights to work when breaking.Wire Set up: Disconnect original/stock lights. pull wire out * note there are some clips that go up down and up underneath where it feeds through. Make sure to not break them and slip them out one by one. These are some of the hard to reach areas with your fingers but you'll soon get the wire free. once wire if free. feed new light wire through till it reaches the battery. Insert each wire through fastening connector one by one. From right to left I inserted Black, Yelllow, White, and Red wire last on your left side. make sure black meets with black and follow this order. By black to black I mean, your wire that you are connecting too has a black wire make sure your connection lines up in the order i just described.Result: After all the hassle, fasten wire underneath tire cover just how you removed the existing same way just in reverse. Use same clips and everything. ALSO I ALMOST FORGOT!! The mounting screw it comes with will work only if you somehow manage to take the back off which is too time consuming. or taking the whole back tire off. but thats just too much for a break light install. SO, just use the same bolts used for the original. They will fit. Don't. worry.ALL IN ALL, great product looks clean. took a little time but definitely worth it. ENJOY.

Very high quality. Was impressed with everything except the fact that my 2010 883 is three wire and this is four wire so therefore you can either not use the yellow turn signal and just have it blink red or you can have the yellow and red come on with your turn signal and your brake. The bolt being too short was not an issue I just reused the bolts from my old one. Overall very happy.

Worked great! Easy install, popped my rear fender off & strut bars ran the wiring an hooked the new wiring to my original HD connectors. I also wanna say this my bike is a 2012 Softail FXS. I had very few modifications but overall job took 2 hours.

This lights flickers when on, they are misconfigured in a way that they all light up at the same time, braking light don't ever go down.Missing wire diagram.Built quality feels solid.Can't tell if they feet on the framd, never made it that long.Wasted my time troubleshooting to make it work and least seller should reimburse for labor wage plus returning time wasted.

The lights were exactly what I needed for my 01 883,fit perfectly but the bolts that they came with were just a hair short so had to get new bolts,other than that they were just what I wanted

Very impressed. Arrived quick and bubble wrapped real nice. The paint on them is nice (black) and the quality in my opinion is top notch. Instal was a snap besides having to go to lowes and buy longer bolts. Wasnt too happy about that but oh well..only cost me 4 extra dollars and an hour of my time maybe. After that zip zap ..im done. We're no instructions so you have to use the wire diagram on the sellers page but its not rocket science bro. On my wideglide..they stick out a little farther than my stock blinkers did..but that actually works better... for me anyway. Bright tail and stop brighter. Nice bright turn which is yelow/amber like its suppose to be. Im good with this..id recommend. Sure.