YONICO Tongue and Groove Router Bits Set Up to 3/4-Inch Stock 1/2" Cutting Depth 2 Bit Set 1/4-Inch Shank for Edge-to-Edge Hardwood Flooring, Paneling, Cabinet Door, Plywood Sheathing 15221q

After observing a You Tube video demonstrating tongue and Groove cabinet doors, I purchased Yonico's tongue and groove router bits. I've done a lot of woodworking but have never built cabinet doors. These router bits worked well and saved me a bunch of time. First, they are easy to use. They are designed for 3/4" stock which means adjusting the height of the bit means lining up the tongue cutter with the top of your 3/4" rail. It may have been luck, but my first rail cut on a test piece left a 1/4" on each side of the tongue. Likewise, when using the groove cutter you align your test piece tongue with the router bit. Again, the cut was dead on. With minimal sanding of the rails, I was ready to glue. I used 1/4" baltic birch for the door insert. It was not as snug as the rail and stiles but was tight enough and left room for expansion. The bits easily cut through Select Pine. The edges were crisp with no tear out at a speed of 12,000 on a standard Skil router. I can't speak to durability but for these two doors the setup and execution couldn't have gone better. The bits are heavy and well made. This is a great value, half the cost of other brands but clearly accurate. The simplicity of use is the best characteristic. The only concern is a lack of instructions. However, with you tube there are multiple videos that will walk you through this process of building cabinets.

Needed this for t&g 3/4 subfloor project. If you save one sheet of 3/4 ply using this set, it pays for itself.

I will start by saying that I like these bits. As other reviews state, they aren't perfect. I used them to make shaker style cabinet doors out of 3/4" premium pine and, after using several pieces of scrap, decided that there was no way to get them to not leave a small shaving of wood on one edge of the board when using the tongue cutter. However, this was easily removed with a sharp chisel and, after sanding, my doors look great. So, while you might not have that one extra step by going with a higher priced set, these worked great for my needs and the price was a big bonus. I will gladly trade the 60+ extra dollars for a small amount of chisel work.

My router spin faster than many, so I had to be rather particular about buying higher quality router tools that support the higher speeds. I've already used these tools for multiple projects and am very pleased with them. They even come in a really fancy box which is super nice as otherwise the parts would likely sit bashing around in some box.

Gave this a test run and worked great. Good smooth cuts. Now that i have been using these bits to make a table I have more to say. MY test run was on 1x3 pine and the cut was perfect so i moved on to oak. I adjusted the height and adjusted the height and adjusted the height until i needed a beer and no matter how many adjustments I made I was always left with a little sliver uncut. It turns out 1x3 oak is just a sliver thicker than 3/4 pine and these bits are precise for 3/4" wood. My bad and not a big problem. I just took off the sliver and I'm good to go. My advice.... Check your dimensions and make sure it's exactly 3/4 before you get frustrated like I did. Stated wood dimensions are not guaranteed. Oh, The bits work great.

I have a small woodworking shop at my home, and have recently begun to learn the fundamentals of wood joining. I had used several Yonico router bits for some decorative wood finishing, so when I began tongue and groove joining I wanted high quality router bits to help me accomplish the task. These Yonico bits offered reliable and quality performance, and provided the fastest and best finished product I could hope for. I recommend the Yonico Router Bit product line to everyone! Best of luck! Jim Benson :-)

Seems to be a good quality and cuts well but the tongue is not adjusted wide enough for the grooves. I had to order shims to space the tongue to make it larger for a tight fit.

Vuen producto lo recomiendo

Buenas brocas a un precio adecuado para uso en talleres pequeños con corridas de produccion cortas o para aficionados. La recomiendo, son de buena calidad. No estan a la altura de una Freud o Amana pero son buenas.

Rien à dire

Me gusta usar esta marca de brocas porque el filo dura mas que el promedio de otras brocas. Buen producto

This one took awhile to arrive, but mostly because it was retained on my country customs not seller fault... i'm just a DIY kinda guy, but with this set of bits i feel like a professional.

Surprisingly cuts really well 👍