[GM・フォード・クライスラー採用] ルームミラー (バックミラー) 専用 接着剤 (フロントガラス用)

修理工場でガラス交換と言われたBMWですがこれ1本で解決しました。 ガッチリと固定されて安心できます。 修理代数十万円の代替としては素晴らしすぎます！

さすが本物。少面積でも確実に接着します。説明書が英語で分かりにくく、アンプルを割って使ってしまいました。

20時間でくっつくとの事だったのですがつかなかったので、2度お問い合わせしたのですが、2週間たっても全く連絡いただけません。 こんな対応はじめてなので驚いています。

I have been a mechanic for over 20 years. I just decided to order this because it was quick, I was low on time, and it was my personal vehicle. I've used them before, and they are what they say they are. However, this time it didn't stick right away. I followed the instructions on the package, but the mirror fell off in 24 hours. There was enough left in the package that I was able to make a second application, again cleaning the re an whatnot. This time, it worked like a charm. Just as I expect. So if you mess one up, don't panic! It will be ok :)

Bought this gasket maker for my project truck and it is highly recommended for those that need a gasket in a pinch!

Been a couple months now and send to be holding well. Just happy to have a rear view mirror again

The rearview mirror on my 2001 Jeep fell off sever years ago. I don't drive often anymore. I bought a light plastic mirror from Amazon and installed in my Jeep... not the best option. I did eventually get it to adhere to the window, but eventually my Aussie knocked the mirror off... so for the past year, I've tried to reapply the plastic mirror, which would remain attached for a few days and fall off, basically I've had no mirror for the past year, but since I don't drive much, wasn't an issue... but because I don't drive, the battery went dead and I had to apply the trickle charger for a few days and now that I have the battery recharged, I will try to keep the battery charged by driving a few times a week, but to do so, I need a rear view mirror. So I decided not the purchase another mirror but to try to reattach a mirror. I still have the original mirror, but it is heavy. I also have a mirror similar to the original but lighter that attaches like the old mirror, so I decided to attach this mirror. I did some research and determined how to reattach a mirror and this adhesive Kit was one of my options. The kit was also less expensive than a new mirror. So, to make a long story short, I bought the kit and yesterday (10-16) I made my attempt to reattach the lighter replica of the original mirror. I read the instructions 4 or 5 times. I did several dry runs to make sure I was getting everything in it's proper place and that I was applying the glue to the appropriate side, etc., etc.... One of the instructions was to squeeze the Part A activator ampule until the vial breaks. There is a small sponge on the top of the ampule and after observing the ample for a few minutes, it was apparent that the "vial" separates the liquid activator from the sponge and I should squeeze the ampule at the top near the sponge to break the vial, and after several minutes of squeezing the ampule, the vial didn't break. I squeezed some more with no success, so I found small pliers and used the pliers to gently squeeze the ample near the top and after a few attempts, the "vial" broke. I could see the broken vial in the ampule. I had cleaned the window as instructed and also the holder that I glued to the window. I applied the activator as instructed to the window and the mirror holder. I waited 5 minutes as instructed. I then applied the glue to the holder, making sure the holder was in the proper position and held against the window for 1 minute. I could actually see the glue harden around the edges of the holder. After 1 minute the holder appeared to be firmly affixed to the window. I slide the mirror in place and made several adjustments on the mirror with absolutely no movement from the holder now firmly affixed to the window. This was yesterday. All appears to be a go with the mirror now firmly attached to the window.

Used this twice. First time due to user error. Second time followed the instructions exactly as described and even taped the button to the mirror and left it there for an hour before applying my mirror housing. Immediately came off once a little bit of rotational force was applied.