MA410M

Keeps cpu at around 28 to 36deg.

I liked the look of the cooler and the rgb is really good, however it was a bit of a pain to install, as youll have to move the fans to fit it onto the motherboard, just pay attention to the fans as you will have to flip one around to prevent air flow issues inside your case, it also tall enough to fit your ram under as long as you dont have very tall ram dimms Likw most PC components, the manual that comes with it was lacking and could be more clear or easy to understand

Cooler performs okay but is overpriced. Mounting mechanism sucks and RGB uses older 12v style not 5v ARGB meaning it only does one colour at a time.

Really nice good looking glad I got it my cousin runs at 75 max while playing games would I prefer it a little cooler yes but not gonna break it and it looks awesome so overhaul glad I bought it I'm running a amd 5600x processor I have 16gb of ram if u are running 32gb ram the cooler may block the slots

Has to work hard to keep temps below 90

Good cooler, great performance, but because of the lowness of the profile really limits the types of ran you can use...

The only thing I can say about item is.................. Its absolutely terrible horrible fitting rgb didn't work couldn't put the side of my case on properly because of how big this ridiculous cpu cooler is. If I were you don't go for this go for something else.

I upgraded to this cooler from my AMD stock cooler (Wraith Stealth). Previously I was idling around 35/40 degrees C, but with this new cooler I idle around 25 C on my Ryzen 5 1600. While playing games (PUBG, TF2 etc) I haven’t seen my cpu get past 35 degrees under load. The RGB looks fantastic and comes with a controller in case your motherboard isn’t RGB compatible. The installation instructions were easy to follow, for the AM4 socket it only used 6 sets of the parts included. However, I had some difficulty trying to screw in the cooler for the final screw because it was right underneath the fan/aluminium fins. Included in the box along with the cooler were every tool and part I needed, including standoffs, backplate, thermal paste, etc. Overall this is a fantastic air cooler and I would buy this again for another build.

So far my desktop is functioning perfectly no hassle or glitch since it was installed.

Op en top geleverd perfect thx guys

This is a fantastic product and it is VERY good looking. It displays RGB colors in the fans and inside the cooler itself. It has a “tunnel” down the middle which shows a holographic light effect. There is a small controller to set the lighting mode. It is attached to a metal surface inside your case with an internal magnet. Many lighting modes including a “temperature-gauge” mode that changes with processor temp (load). The mode can be set using: a) the buttons on this small controller b) by connecting the controller to a 9-pin USB header on the motherboard then using their free software (“USB Male to 5 Pin Motherboard Female Header Adapter Cable” required) c) By connecting cooler to an RGB-enabled motherboard The unit is nearly silent at low CPU loads/temps and quiet even at full speed. It provides airflow over the DRAM sticks, with the air flowing from the front of the case to the rear. It requires a high clearance above the motherboard, so you need to have an appropriate, “deep” case. It is a tight fit next to the DRAM sticks, but it is obviously engineered to be that way. It is not an easy installation, but it is very doable with the patience to follow the steps, which are provided in a “picture only” instruction pamphlet (less translation with no words). Access to the back of the motherboard at the site of the processor is required so if your case doesn’t have that access, you will need to remove the motherboard. There is a tiny wrench included to tighten the cooler to the mounts on the motherboard, but I found it impossible to access the screws from the sides, as the instructions show. Instead, I removed the two fans from the cooler which gave me straight-on access and allowed me to easily tighten the screws with a screwdriver, from above. Each fan is attached with 4 knurled screws which can be removed and reinstalled with your fingers. This too was obviously engineered that way, it’s just too bad that the instructions don’t mention that feature or that method of installation. It would have saved me hours. The kit contains a TINY tube of thermal compound paste, which you should throw away and, instead, buy a tube of real paste with 4 grams of compound. The contact pad has four, double-ended heat pipes which go up and through the cooler and I am sure that heat conduction, away from the processor, is as good as it gets. So much more than the Intel cooler that came with my chip. There is one glaring problem. There is no support available. I searched their website and could not find any way to contact Cooler Master other than to request that a service ticket be opened. I did that and never heard anything back from them. Amazon offers "support" on the pages from which I ordered but they could only offer to transfer me to Cooler Master. I got an 800 number from them, which I later found on their website, but always got a VM that stated their hours and said they were too busy to answer the phone and then it hung up. I tried for days at different times of the day and NEVER got them to answer. All I wanted to do was find out if my motherboard was supported and if they had any more installation suggestions. Luckily I figured it out myself and removed the fans as I stated earlier. All-in-all, I am extremely pleased with this cooler and I feel that the price would be reasonable even if it were doubled. It is a very good-looking addition to my setup – see my attached pictures. BTW: I purchased the $9.99 Protection Plan which would probably be a good idea for anyone else.

Intel i5 8400でﾍﾞﾝﾁﾏｰｸを回してまくっても50℃を越えることはありませんでした。 ただ取説は絵のみで少々悩みました(一部絵がおかしい)ｹｰｽから取り出しても大きい為 取り付けは少々コツが要りました。 タイムセールで安かったのとASUS製H370TUFﾏｻﾞﾎﾞを使用しているため購入。 統一感があり満足です！ コラボケースも欲しくなります( ☆∀☆)