Electric Guitar Pickup Double Coil Humbucker Pickups 50mm Ceramic Neck Pickup-Black

This is a review of the neck version. Now, granted, I am not as picky about neck humbuckers as I am about bridge humbuckers, but this thing exceeded my expectations, big time. Sounds almost as good as a DiMarzio PAF Pro in the neck position, and that one is my favorite. But the real treat is how the -- what's it called? A "Flee-or"? -- sounds when you split the coils. Its single-coil sound is simply lovely. Appearance is as good as any of the name-brand pickups. I got the zebra version and the cream-colored coil was exactly the right shade. Comes with a peel-off plastic film; that's a nice touch. Overall build quality is very good. I can't believe I got this thing for 12 bucks. It's as good as pickups that cost 6x as much.

I bought a Schecter C-1 Platinum for $100, problem was the previous owner took out the old pickups. I didn't want to spend much on a new pickup set, I could've bought a used set of quality pickups, but even that is around $80-90. I'm cheap , and pretty much broke so I just took a chance on these. I've been playing guitar for 14+ years, tried MANY pickups, by Dimarzio, Fluence, EMG, Seymour Duncan, etc. I'll be realistic, these Chinese pickups aren't as great as any of those name brands, but they're pretty damn good for $13. They're high output and have a good high gain tone, and sound pretty decent clean. I wired in a push/pull pot to get some single coil sounds out of them too, they're not too bad clean, i've heard better, but they get the job done..... They look decently made, the wires aren't super long but they were long enough for me. They got a nice clean look too. I mostly use amplifier sims like BIAS FX, Guitar Rig 5, and have yet to use them in a "real" amplifier, but through my set up they sound pretty good. As good as my Fluence pickups or Dimarzio's in my other guitars? No, but not too far. I mostly play hard rock, metal, and shred like Satriani, Vivaldi... They do a good job... You just have to remember, your amp setup is far more important than your pickups. So if you're looking for a massive tone upgrade with ANY pickup, you will be disappointed. Pickups will help you get closer to what you want, but they will not be the main source of your tone. Just thought i'd mention that to any noob out there looking to upgrade! Good buy! for $13 you can't really complain

This is second set of Alinco type Fleor Humbucker pickups I have purchased and installed in built guitars. This set was well made and length of wires were good and enough for installation. Bought these as a little cheaper than first set. Used in a coil split project which they worked well. They are a little bright in tone but have good overall sound and dynamics, for purpose of my build. For the money very good product, and sound pretty close to the pickups in a Schecter guitar and PRS SE standard I havfe. CAn't compare to Semour Duncan or other expensive brands. Wiring would follow Semour Duncan type. Would recommend them to anyone doing a build or replacing pickups.

These pickups get 5 stars primarily for bang for the buck. However, they are certainly useable pickups. Please note that tone is subjective and others might have a different opinion about the sound. The pickups came wrapped in foil inside a plastic bag which included separate bags for the screws and springs. I cut the springs to make installation easier. The wiring is four conductor. Back is hot and goes to the pickup selector. The green wire and bare shielding are wrapped together, as are the red and white wires. In this configuration, the pickup is in dual-coil mode. I soldered the red/white wires to a switch which connected to ground. With the switch engaged, the red/white wires were connected to ground and the pickup operated in single-coil mode. I checked resistance and both pickups were as advertised. I installed the pickups in a Strat-style partscaster set up for two humbucking pickups. With my amp on the clean channel, the pickups sounded decent but not necessarily outstanding. With both pickups engaged, they produced a clean, bright sound. In single-coil code, the pickups sounded thinner with more treble. While single-coil mode provides another tonal option, it's not a substitute for a single-coil pickup. On the high-gain channel, the bridge pickup sounded especially good. The distortion was not harsh. It sounded good in single-coil mode. The neck pickup is OK. These pickups are a great deal if you are assembling a guitar out of parts and want something to use until you can afford better pickups. I'm an amateur player and the sound certainly is good enough for me.

La recomiendo. Tenía muchas dudas porque había oído muchos buenos comentarios de wilkinson pero siendo estas un poco más baratas y sin tener tantos comentarios ( no buenos, sino en global, positivos y negativos tenía pocos ) no me atrevía a comprarlas. Al final lo hice y compré seguidamente antes de probarlas las de la marca anteriormente mencionada. El sonido es igual en ambas marcas. Igual de bueno, debo añadir, porque siendo xxx veces más baratas que las famosas "Duncan Du" proporcionan un sonido excelente.

Clean and high gain pickup, very nice pickup, sound loud and well sustainable, love it

Para el precio estan muy bien, me gusta que tengan 4 cables por pastilla para poder hacer combinaciones, no son las mas brillantes, tienen un sonido equilibrado

They sound better on my deluxe tele than a few other pickups I tried in past years. More vintage like when rolled off and decent grit when volume is up.

Preso per sostituire il single coil di una telecaster al manico. Per il prezzo pagato non si può chiedere di più, ho avuto modo anche di splittarlo e quindi tornare al suono da single coil qualora ne avessi bisogno. Unica accortezza, attenti al cablaggio, attenetevi alle istruzioni riportate sul foglietto del pick up e lasciate stare i vari siti tipo dimarzio e seymour duncan, perchè per esperienza posso dirvi che ogni produttore cambia i colori dei vari poli del pick e potreste incorrere in una configurazione sbagliata. I fili saldati insieme dovete semplicemente nastrarli con dell'isolante nel caso in cui non dobbiamo splittare il pickup. Il filo di massa va collegato insieme a quello scoperto. Il restante al selettore. Per essere sicuri procuratevi un multimetro.