Rust-Oleum 200041H Varathane Ultimate Polyurethane Interior Wood Varnish/Finish (Water-Based | Gloss Clear | 946 ML)

Used for furniture woodwork. Cost in India is just the same as in US (if rounded), so, it's on the expensive side. But it gave SO GOOD look! Easy to apply, doesn't smell bad or hurt. Five stars!

Very good product I used the varnish and the wood polish both on my dining table . Fantastic results. I am very happy. Better than anything you will get in the market.

Really excellent & easy to use leaving a great finish. I immediately bought a second can!

I used this product for finishing a live-edge acacia slab coffee table and it worked beautifully, bringing out the grain without darkening the wood too much (Indian acacia wood tends to turn red over time) or giving a plasticky look or feel. I did get some raised grain (because of the water) but it was easy to handle with a light sanding between coats. Product was delivered on time and in good shape. Wish the seller also gets smaller unit sizes as I'm left with an almost full can after finishing the table :)

Easy to apply. Almost clear! smooth finish, but not as thick as oil based polyeurathene

Really good product

Easy to use..easy to clean up

Excellent product but expensive

جميل جدا، ويعطي حماية ممتازة ، بالإضافة إلى انه لم يؤثر على لون الخشب الطبيعي ويجعله يصفر قليلا

Easy to apply. I applied 3 coats as recommended waiting few minutes/ hours between each layer , semi gloss, semi shine, and most importantly is water proof. Never regret. However , it’s little expensive in Amazon comparing to local market.

Best quality and will get it again.

I have used this varnish for several applications, three of which I'll describe here. I've been varnishing my rat cage with this stuff for 20 years. I made the cage myself out of an unfinished pine bookcase to which I attached pine-framed screen doors. I originally got the varnish on the suggestion of a Home Depot associate who said that it was non-toxic when dry, which is essential for small animals who would be sleeping on the varnish and who like to chew things. This varnish takes some heavy punishment. Although my rats use litterboxes, as soon as the boxes are a bit dirty they start using the corners of the cage instead. That means that there is often urine (and all sorts of foods, from fruit to oatmeal to gravy) drying on and sticking to the varnish. This is not a problem for the varnish: it cleans right up with water and a damp paper towel. But to really clean the cage, I spray isopropyl alcohol on it every five to seven days and scrub with a towel. After about 2 or 3 years of this abuse, the varnish starts to wear thin in places and needs recoating. I never follow the directions, which say that I have to sand the existing varnish before recoating. I just thoroughly clean and dry the shelves and then paint on a couple more coats. I have never had the varnish flake or scratch under these conditions. I live in a very old house whose demise is imminent, so remodeling is always on-demand and slap-dash. Recently I had to get rid of some old carpet. In one room, the floor was literally nothing but bare plywood with lots of paint drips and plaster from earlier room remodeling. In the other room, there was a pretty parquet wood floor, which had been ruined by a VERY thorough application of carpet glue in ridges about 1/6in to 1/8in high. The house is not going to be standing much longer, so to get through the remaining 3 years I decided to use polyurethane--it was good enough for the rats, so why not for me? Last year, for the first room with plywood, I mostly followed the directions, which say to use a brush and make small strokes. This is supposed to avoid bubbling. I applied two coats without sanding in between. The results were outstanding: the splashes of paint and plaster on dark plywood under the high-gloss varnish give the room a sort of shabby industrial chic. I've single-handedly scooted the heavy (high efficiency) washing machine back and forth several times over the varnish and it didn't scratch, even in the places with raised blobs of paint or plaster underneath. It's been a year and even the high traffic spots between doors and the areas that get year-round sun look like they were just painted. This year I had to uncover that parquet floor with the glue on it. This room gets much less traffic (bedroom), so I cared a lot less about the paint bubbling. And I was in a big hurry to get it done. Painting a floor with a brush is not my idea of a fun home project. I decided to do what is absolutely forbidden by the instructions: use a foam roller to apply the varnish, right over the lines of glue, and over the mysterious 7-inch-wide bands of duct tape that ran across middle of the room. (Did not want to find out what was under that tape!) Because the glue lines were so high, I put down 4 coats of this very thin polyurethane varnish instead of just 2, so that I could more easily dust-mop the room. Again, fabulous results. I cannot find a single bubble in the paint, despite having hurriedly used a roller for all 4 coats. The varnish is adhering just fine to the duct tape; I think the tape will peel up before the varnish comes off it. The rough, scratchy ridges of glue are now smooth and comfortable to walk on. I like to think of the glue as a feature: no-slip flooring for when I wear slippery socks. I really liked using the roller to apply the paint. It's easy to see where you've just painted because the roller makes a much cloudier application than a brush, but still dries crystal clear. I care for my flooring much better than the rats care for theirs, so by the time this varnish starts to show wear, this house will have been demolished. The third application for this varnish is as a top coating over primer. On built-in shelving and inside drawers in this house, I have applied Kilz white mold-inhibiting primer, because a roof leak caused a mold problem. After fixing the roof, I spray treated all the drawers with a mixture of isopropyl alcohol and grapeseed extract, then applied Kilz primer. I would have been happy to leave it at that, but primer is a terrible surface to deal with, sort of powdery in texture, impossible to slide anything like clothing on it. I haven't found any normal paints to be good for shelving, probably due to the humidity in this region--everything sticks to the paint and it gets peeled off the shelves. So, given the great results with the rat cage, I decided to try varathane. On top of the single coat of Kilz, I applied a single coat of varathane. All problems solved. The mold has not returned after 6 years, and the surfaces of the drawers and shelves are still shiny and slick. EXCELLENT product.

Love this product. Went on great and drying finish was lovely. Would recommend this highly