2Sets Mouse Feet Pads Skates Compatible for Razer Viper 8KHz Gaming Mouse (for Razer Viper Wired)

Fits perfectly on the Razer Viper Ultimate! I highly recommend it as a solution to the well-known Razer finger grip issue, especially for those whose skin tends to wear down the rubber material on older models. This tape provides a strong, firm grip while covering and protecting the original material on the mouse. It’s an excellent choice for gamers who want to maintain their trusty mouse in great condition. Totally worth it!

So, I spilled a drink near my mouse, it still worked fine, but I found that one of the side buttons was sticking, so I needed to be able to open the mouse up and give it a deep clean. To do that, I needed to remove the stock feet.This set worked perfectly as a replacement. They have a precise fit, weren't too difficult to apply, and feel just as good, if not better than the originals (which admittedly were wearing a bit thin after 2+ years of use). It allowed me to resolve my sticky button issue, and even lube up the posts on the left and right mouse buttons to help alleviate the infamous "squeak". My mouse feels as good as new again and it saved me from needing to buy a whole new mouse.To anyone complaining about these not fitting, you need to read the description a little more carefully next time. This is for the Razer Viper ULTIMATE (the wireless version of the razer viper). Do NOT buy these for the wired Razer Viper or the Viper Mini - those are different products. To the person who thinks the feet feel like sandpaper on your mousepad - you need to remove the white protective stickers on each after you've applied them. I get that the instructions aren't very clear on the packaging, but it's pretty straight forward.NOTE: You WILL want to carefully examine the orientation of the foot in the middle that sits around the mouse sensor. At first glance it looks like you should be able to apply it either direction, but that's not the case. One end has more highly defined rounded corners - that end needs to be facing downwards, beneath the sensor.

Reccomend using a flat head screw driver to get the thick plastic removed from original skin. But the grip feels so much better! Perfect fit!

I got this to replace the worn out grip on my mouse. Could probably have just stuck it right over the old grip, but it'd been worn down so bad that the new tape just conformed to all the divots and looked terrible. I dug out the old grips and just put these new ones on the bare plastic and it's worked great for ... 9 months so far? The only thing that didn't work as well as I would have liked was the thumb buttons. Just because it's a small contact spot and the surface is curved, the thumb button tape came off after a while, but the main grip has held up very well!

The replacement grip tape comes on a 3M pad, just like the Razer official tape that comes with newer mice, plus a handy alcohol wipe to really clean the surface. Applies simply and fits snuggly, thickness aligns with the raised middle surface. 5/5 this is what you want for your Razer Viper Ultimate, just make sure you peel off the original grip and scratch off the the thin layer of foam beneath, down to the plastic.

So first off, these grips are meant to go over the ones the come on the Viper Ultimate, but I was really interested in replacing the worn out grip that's on the mouse rather than covering it up. So, I took a knife and carefully peeled away at the stock side grip. It is NOT a sticker, it does not come off easily, but I did manage to get it off with about five minutes of peeling and careful scraping. Then just applied the new grip and voila!One thing I'd caution to anyone doing this: there's a layer of rubber under the stock grip that you can easily gouge out, which will leave the new grip feeling lumpy. Try to be careful if you go this path, and if you do gouge some of it out, maybe fill it in with something (like a glue or putty), let dry/set, then put the new grip over it.

Been using the grip tape for over a year on a heavily used Razer Ultimate Wireless. Wasn't completely worn out, but the edges had started to pick up cat hair. Replaced it with the same thing. The old tape was still solidly adhered, but left no residue when I peeled it off. Both the old tape and the new tape fit perfectly and have a good grip. Highly recommend.

I purchased one of these units in 2021 and after 10 months several pieces started falling off of the mouse. I assumed I had just received a unit with bad adhesive, so I purchased another one about 9 months ago. It is now failing in the same way, with the thumb pieces and edges rolling up and no longer adhering. The pieces that come off are tacky like a post-it note, but no longer adhere tightly as they did when new. This to me indicates the adhesive they are using degrades quickly over time, and does not hold up for long-term usage. I only use my mouse about 2-3 hours a day, so this isn't something that is being overly used. I otherwise liked the product, but unfortunately I cannot recommend it to anybody. It doesn't matter how well it works if it breaks inside of a year becoming completely unusable.