Question 1

I love Makita tools.  But "Low AMP draw" is a suspiciously weaselly way to state power consumption.  WHAT IS the EXACT MAX AMP draw?

Accepted Answer

13 amps. So a residential 3 prong (15A) outlet should run it, if plugged in directly and no other loads on the circuit.

Thank you Professor McGraw for taking this opportunity to teach us all a lesson in electrical theory. Your answer is noted. And your answer is discarded as not an answer but another "weaselly" way to avoid actually answering.
Actual "thank you"s to Maple Jack and I Give...Savage for practical answers.

Every air compressor brand seems to think that telling us users the horsepower rating is super important. 
As if we users are out here on jobsites pulling out air compressors and comparing HP numbers like jock sizes. 
Most of us are more concerned with: "Can I run this compressor on a 15 amp 3 prong outlet with a 50 ft 12/3 extension cord?" It looks like the literature includes a reference to 12.5? amps. Why this information is buried in the user manual and not boldly decal-ed on the unit is beyond my personal comprehension. The 2.5 HP rating is only the start-up under pressure, and has absolutely no bearing on anything, unless you want to compare jock sizes with the other guy running a DeWalt.

Maple Jack points out that extended run times have caused his unit to trigger a 15 amp breaker. I assume he was probably using a 12/3 extension cord, probably less than 50 ft. Savage has similar advice. And they both point out that extension cords, even very good ones have a cost to the energy supplied. (Inversely proportional to the AWG of the wire and directly proportional to the square of the run of the wire, I think). If the compressor has an "unloader valve" then the pressure at the cylinder should be close to zero PSI at re-start, reducing the surge current required. If the compressor has a start capacitor, then the surge current is largely supplied by the capacitor. (no literature on either component) If it makes a difference, the 12.5? AMP rating is based on a 110v/60Hz supplied power; I use a generator with adjustable voltage or a 220v/30A transformer for most of my jobsite power. You'd be surprised how much happier all my tools are getting 118-122v/62-65Hz

All that theory aside: this compressor will probably prefer to be plugged directly into a 15 amp receptacle. Extra air hose is better than extension cords for most occasions.

Question 2

Is there an exploded view of componets?  Compressor will go to 40 lbs and no further. Where do you start looking to replace parts to resolve?  Thanks

Accepted Answer

You can easily download the parts breakdown for this compressor from the Makita website.  Here is the link below.  Once there, download the Parts Breakdown pdf file. http://www.makitatools.com/en-us/Modules/Tools/ToolDetails.aspx?Name=MAC2400

Question 3

what brand and weight air compressor oil should I use?

Accepted Answer

I bought one of these from Amazon 3 years ago and I like it.  It comes with enough high quality synthetic oil for one filling.  The owners manual (which is downloadable before you purchase) tells you about the type of oil and the change intervals.  Generally speaking, after you have used it for a hundred hours or so, change the oil with a top quality synthetic air compressor oil, of the weight specified in the manual for your climate and work conditions.  More important that that, drain the water out of the tank every day after you use it.  You should consider getting oil and water traps if you plan to do any painting with it.  Pay attention to hose size and fitting size if you plan to use hoses over 25 feet long (3/8” hoses have 225% more flow capacity than 1/4” hoses).

Question 4

Can I use for 110 psi RV tires?

Accepted Answer

Just a guess, but don't see why not. It has a max of 130 PSI.  Just dial up to 110psi  on the right side gauge and while it may take a bit longer it should work just fine. I would get a second opinion however since I've only used for tires that are 90psi max so far.

Manufacturer	Makita
Part number	MAC2400
Item Weight	36.7 Kilograms
Product Dimensions	50.8 x 45.72 x 47.63 cm; 36.74 kg
Item model number	MAC2400
Size	One Size
Color	Turquoise
Style	MAC2400
Material	Cast Iron
Pattern	Air Compressor
Power source type	Corded Electric
Voltage	120 Volts
Horsepower	2.5
Maximum Power	2.5 Horsepower
Item Package Quantity	1
Air Flow Capacity	4.2 Cubic Feet Per Minute
Noise Level	79 dB
Special Features	Portable
Included components	2 1/4" Universal Quick Coupler, Male (447013-E)
Batteries Included?	No
Batteries Required?	No

About Us

Customer Services

Customer Support

Regional Access

Legal & Policies

Social

Get the App

Makita MAC2400 Big Bore 2.5 HP Air Compressor

Details

Description

Specifications

Have a Question? See What Others Asked

Common Questions